background image

Preparing for Use

R&S

®

TSME-Z3

16

Getting Started 1519.0994.02 ─ 02

2. Connect each mobile device to the system unit using a USB cable (max.

three). See also 

figure 3-1

.

3. Connect the control PC for the mobile devices to the CPU connector on the

system unit.

3.2

Completing the Pre-Configured Measurement
System

The R&S

 

TSME-Z3 is pre-configured in the factory according to the user's specifi-

cations. Thus, you only have to connect the additional equipment to complete the
measurement setup for scanning or testing mobile devices.

To complete the measurement system

1. For scanning:

a) Using a LAN cable, connect the control PC for the R&S

 

TSME(s) to the

"Host" connector on the system unit.

b) Connect the R&S

 

TSME antennas to the R&S

 

TSME(s).

c) Switch on the R&S

 

TSME(s) and the control PC.

2. For mobile tests:

a) Insert the mobile device(s) in the mobile device holder(s) on the system

unit.

b) Using a USB (type B) cable, connect the control PC for the mobile devices

to the "CPU" connector on the system unit.

c) Switch on the mobile device(s) and the control PC.

 

Completing the Pre-Configured Measurement System

Summary of Contents for TSME-Z3





































Reviews: