background image

 

www.rojaflex.com

    

  

19

Declaration of Conformity

Declaration of conformity

Konformitätserklärung

 

ORIGINAL EU/EC DECLARATION OF CONFORMITY 

ORIGINAL EU/EG KONFORMITÄTSERKLÄRUNG

We, Schoenberger Germany Enterprises GmbH & Co. KG, Zechstr. 1-7, D-82069 Hohenschäftlarn, Germany 
declare under our sole responsibility that the 

Rojaflex 

branded product:

 

Wir, die Schoenberger Germany Enterprises GmbH & Co. KG, Zechstr. 1-7, D-82069 Hohenschäftlarn, Deutschland 
erklären unter unserer alleinigen Verantwortung, dass das mit der Marke 

Rojaflex

 versehene Produkt:

Document no. / Dokument-Nr. 

 

 

CE_ROJ_MLS_MLM_2022-02-01   

(Update LVD 2022-02-01)

Brand / 

Marke 

 

    

Rojaflex  

Model / 

Modell  

   

MLS-10/17, MLS-13/14

      MLM-10/15, 

MLM-20/15,MLM-30/15, 

MLM-40/15 

  

   
Product Type / 

Produkttyp 

 

 

 

Motorisation for shutter, awning, blind and similar equipment 

 

 

 

 

 

 

Antriebe für Rollläden, Markisen, Jalousien und ähnliche 

      Einrichtungen

Serial number from / 

Seriennummer ab:  

 

xx_02_2022 

(day/month/year) or 05/22 (week/year)

when uses as intended, according to his instructions, complies with the essential requirements of the following 
directives: 

den einschlägigen Bestimmungen der folgenden Richtlinien entspricht, wenn es nach den Anweisungen des Herstellers 
bestimmungsgemäß verwendet wird:

Machinery directive 2006/42/EC 

Maschinenrichtlinie 2006/42/EU

Electromagnetic compatibility directive (EMC) 2014/30/EU

 

Richtlinie Elektromagnetische Verträglichtkeit 2014/30/EU

Low Voltage Directive 2014/35/EU 

Niederspannungsrichtlinie 2014/35/EU

Restriction of the use of certain Hazardous Substances directive (RoHS) 2011/65/EU and 2015/863/EU 

RoHS Richtlinien 2011/65/EU und 2015/863/EU

The following standards were applied to assess the conformity: 

Die Konformität wird durch die Einhaltung folgender Normen nachgewiesen:

DIN EN 60335-1 (VDE 0700-1):2020-08; 
EN60335-1:2012+AC+A11+A13+A1+A2+A14:2019
EN 60335-1:2012/A15:2021
DIN EN 60335-2-97 (VDE 0700-97):2017-05; 
EN60335-2-97:2006+A11+A2+A12:2015
DIN EN 62233 (VDE 0700-366):2008-11; 
EN 62233:2008
DIN EN 62233 Ber.1 (VDE 0700-366 Ber.1):2009-04; 
EN 62233 Ber.1:2008

Attestation of Conformity:

VDE

40041739 (MLS)

40041738 (MLM/MLM-NHK)

Hohenschäftlarn, 2022-02

Michael Mayer 

CEO / 

Geschäftsführer

This declaration loses its validity in case of improper use and changes of the system or product that has not been agreed with the manufacturer.

Diese Erklärung verliert Ihre Gültigkeit bei nicht bestimmungsgemäßer Verwendung und bei Änderungen der Anlage bzw. des Produktes, 

die nicht mit dem Hersteller abgesprochen wurden.

Aktuelle EU-Konformitätserklärungen sind unter der folgenden Internetadresse verfügbar: 
www.rojaflex.com/konformitaetserklaerungen.html

Summary of Contents for 9010000





















Reviews: