background image

Roksan Audio ltd

 

 

K2 Stereo Power Amplifier User Manual 

CLASSIFICATION: 

General Use

 

 

Version 1.02

 

All specifications are liable to change without notice. E&OE

 

Page 9 of 11

 

ENGLISH

 

If you suspect that your ROKSAN 

K2

 Stereo Power Amplifier is not operating properly, you should check all the 

connections carefully. Pay particular attention to speaker phasing and channel connections. Phono plugs should 
be fully inserted- a frequent cause of problems is that Phono plug surrounds do not make proper contact. Below 
are some commonly encountered problems with suggestions for possible cure. The list is not exhaustive: If you 
have any unresolved problems, please consult your appointed ROKSAN dealer or distributor. 
 

SYMPTOM 

LIKELY CAUSE 

SUGGESTED REMEDY 

No power 

AC Mains lead not inserted properly 
Unit not switched on at rear panel 

Ensure AC Mains lead is fully inserted 
Switch unit on at rear panel 

No output on one or more 
channels 
 
Lower output on one or both 
channels 
 
Poor speaker imaging, lack  
of Bass output 
 

Missing or bad input signal connection 
Incorrect speaker connection 
 
Higher trim on one or both channels 
 
 
Loudspeakers connected out of phase 

Check all input connections 
Check speaker output connections on 
rear panel 
Check trim level and adjust accordingly 
 
 
Check polarity of speaker connections 
(especially important if Multi-wiring, 
Multi-amping) 

Hum from speakers 

Incorrect Grounding 
 

Check Mains polarity and grounding on 
all connected equipment 

 
 
 
 
 
 
 
 
 

There are no user-serviceable parts inside your 

K2

 Stereo Power Amplifier

. If a fault should develop; refer all servicing to 

your appointed ROKSAN retailer, distributor or ROKSAN approved service agent. 

 

Your ROKSAN 

K2

 Stereo Power Amplifier 

is guaranteed against any defect in materials and workmanship for a period of 

five years

 from the date of purchase. 

 
 

This guarantee only becomes effective if the warranty card is validated by the ROKSAN retailer from whom the equipment 
was purchased and returned to ROKSAN within 

28 days

 of purchase. 

This guarantee excludes: 

 

1.  Damage caused due to accident, missuse, neglect and incorrect installation, adjustment or repair. 
2.  Liability for damage or loss during transit from the retailer or purchaser to ROKSAN or its authorised distributor for the 

purposes of repair or inspection. 

 

Carriage costs to ROKSAN shall be borne by the consignor. 

 

All claims under this guarantee must be made through an authorised ROKSAN retailer. 

 

If equipment returned for repair to ROKSAN is found on inspection to comply with the product specification ROKSAN 
reserves the right to make a charge for examination and return carriage. 

 

Unauthorised servicing will void this guarantee

 
 
 
 
 
 
 
 
 

T R O U B L E S H O O T I N G

 

K

K

K

2

2

2

  Stereo Power Amplifier 

G U A R A N T E E

 

K

K

K

2

2

2

  Stereo Power Amplifier

 

Summary of Contents for Kandy K2












Reviews: