background image

- 5 - 

SAFETY WARNINGS 

(con’t)

 

Risk from Moving Parts 

Serious injury may occur from moving parts 
such as belts, pulleys, flywheels or fans if they 
came in contact with you or your clothing.   

Never operate the air compressor without 
protective belt guards installed.  Replace 
damaged protective covers or guards 
immediately. 

An electric air compressor with automatic 
controls can restart at any time and cause 
bodily injury when least expected. 

Always unplug air compressor and drain air 
tanks completely before attempting any 
repairs or performing maintenance.  Never 
allow children or adolescents to operate air 
compressor. 

Serious injury may occur if repairs are 
attempted with damaged, missing or removed 
protective guards, shrouds or missing covers. 

All repairs to the air compressor should be 
made only by authorized or trained service 
personnel. 
 

 

Risk of Burn 

Serious burn injuries could occur from 
touching exposed metal parts such as the 
compressor head, copper/braided discharge 
lines and engine exhaust muffler during 
operation, and even after compressor is shut 
down for sometime. 

Never touch any of the exposed metal parts 
during operation and for an extended period of 
time after the air compressor has shut down.   
Do not attempt maintenance on the unit until 
it has been allowed to completely cool. 

 

Risk of Injury from Lifting 

Serious injury can result from attempting to lift 
an object that is too heavy. 
 
 

Always obtain assistance from others before 
attempting to lift any object that is too heavy 
for one person. 
 

 

Flying Objects 

Serious injury may occur from loose debris 
being propelled at high speeds from the 
compressed air stream. 
 

Always wear OSHA required “287” safety 
glasses to protect the eyes during operation of 
the air compressor.  Never point the air stream 
or tools at any point of your body, other 
people or animals.   
 
Always turn off the air compressor and drain 
tank pressure completely before attempting 
maintenance or attaching air tools. 

 Warning 

Risk of Unsafe Operation 

Serious injury or death may occur to you or 
others if air compressor is used in an unsafe 
manner. 

Review and understand all instructions and 
warnings in your owner’s manual.  Know how 
to stop the air compressor.  Do not operate 
until you are thoroughly familiar with all of the 
controls.  Do not operate the compressor if 
fatigued or under the influence of alcohol or 
drugs.  Stay alert while operating the 
compressor and pay close attention to the 
task at hand. 

 Caution 

Risk of Damage to  

Air Compressor or Property 

Failure to transport or operate the air 
compressor properly may result in major 
repair expenses. Oil leaks will damage carpets, 
painted surfaces, flooring and other items. 

Check oil levels daily and maintain proper oil 
levels.  Always run compressor in a level, 
secure position that keeps it from tipping or 
falling during use.  Do not operate without an 
air filter or in a corrosive environment.  
 
Always transport in a level position and use 
protective mats to keep truck beds clean, etc.  
Check drain bolts regularly and do not overfill 
machinery with oil. 

 

Please note that this product may not be equipped with a spark arresting muffler.  If the compressor is operated 
around flammable materials or agricultural crops, brush, forests, and grasslands an approved spark arrestor must be 
installed, maintained and in good working order. An approved spark arrestor is legally required in the State of 
California under sections 4442 and 4443 of the California Public Resources Code Statute section 130050.   
 
This product contains chemicals, including lead, known to the state of California to cause cancer, birth defects, and 
other reproductive harm.  Always wash hands after handling this product. 

Summary of Contents for GD4000PV5H
















































Reviews: