background image

- 1 - 

 

 
 
 
 
 

 
 
 
 
 

 

PARTS 

Genuine ROLAIR

®

 replacement parts are sold nationwide through a network of authorized dealers and service centers. 

Please contact the dealership where your air compressor was purchased or our factory Customer Service Department if 
you need help troubleshooting, obtaining parts, or locating an authorized ROLAIR

®

 service representative. 

 
 
 
 

 

 

 

 

 

PORTABLE AIR COMPRESSOR

OWNER’S MANUAL 

WARNING

 

COMPRESSOR DISCHARGE AIR MAY CONTAIN HYDROCARBONS AND OTHER 

CONTAMINANTS! DO NOT USE DISCHARGE AIR FOR BREATHING! 

RECORD OF PERTINENT INFORMATION 

Make a permanent record of the model and serial number of your new air compressor here. You’ll save time and 
expense by including this reference information when requesting service or replacement parts. 
 

 

 

Place & Date of Purchase 

 

Volts 

Model  

HZ 

Serial # 

 

HP 

 
With the tank gauge at 0 PSI and air line(s) disconnected, close drain valve(s) and record the amount of time it takes 
to build tank pressure on the space provided. Periodically test your air compressor against this pump-up time to 
determine if it is operating correctly. If time test is considerably off, contact your local ROLAIR

®

 representative to 

arrange service. 
 

 

From 0 to ______*PSI

From 0 to ______*PSI 

Date Min  Sec

Date

Min

Sec 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To order replacement parts:

1.

Give compressor model number 

2.

Give compressor serial number 

3.

Name of part 

4.

Part number 

5.

Quantity required 

606 South Lake Street > P.O. Box 346 > Hustisford, WI 53034-0346 > 920.349.3281 > fax 920.349.3691 > www.rolair.com 

Summary of Contents for PORTABLE AIR COMPRESSOR














Reviews: