9
Mar. 2008
GT-10
Screw
Important Notes When Disassembling
Guard Against Lost Parts
When disassembling, first check and verify the disassembly procedures, then
carry out actual disassembly operations. Be especially careful to ensure that
the following parts are not lost.
• Jack Bushing (#G2257327R0)
• Insulating Washer 14.5X9.2 (#G2637118R0)
• USB Connector Cap (USBC-1) (#05015034)
Components Mounted on the SW VR
Board
When replacing the LED spacer (#G2147913R0) or keytop unit (#G2497020R0)
on the SW VR Board, first detach LED1 or LED2 and LED3 shown in the
(p. 6), then carry out the replacement.
* When mounting the LEDs, be careful to orient the parts correctly.
Modifying the Wiring
The length of the following ribbon cables differs depending on the production
period. If the length is too long, modify the cable as shown below.
• 3-pin ribbon cable between SW VR Board CN105 and ENC (encoder)
Board CN501 (
A
in the figure below)
• 9-pin ribbon cable between Pedal Board CN202 and Bank Board CN301
(
B
in the figure below)
fig.wiring-set1.eps
Tape Application
After installing the SW VR Board, use Filament Tape #898 (#40122645) to
secure the 2-pin wiring from the LCD unit to the Insulating Sheet
(#G2257331R0) as shown in the figure below.
fig.tape.eps
No.
Part Code
Part Name
Description
Q’ty
a
H5049003R0
SCREW M4X4
NI
5
b
H5049004R0
SCREW M3X10.5
NI
5
c
40563989
SCREW 4X8
TAPTITE S BINDING NI
1
d
40019123
SCREW 3X8
BINDING TAPTITE S BZC
7
e
40011278
SCREW 3X8
BINDING TAPTITE P FE ZC
28
f
40017934
SCREW M3X6
PAN MACHINE W/SW+PW(L) FE ZC
8
g
40342712
SCREW M3X6
PAN MACHINE W/SW+SMALL PW BZC
12
j
40011312
SCREW 3X8
BINDING TAPTITE P BZC
3
r
H5039521R0
NUT M7
5
s
H5039510R0
NUT M9X12X2T NI
7
t
H5039158R0
WASHER M9X14X0.5T NI
6
u
H5039520R0
NUT
M9
2
v
H5039126
M9 WASHER
2
Summary of Contents for Boss GT-10
