Roland Camm-1 Pro GX-640, User Manual

32

Signal 

Number

Terminal 

Number

Signal 

Number

Pin Connection

NC

3 6

1 8

HIGH**

HIGH*

3 5

1 7

GND

NC

3 4

1 6

GND

GND

3 3

1 5

NC

HIGH*

3 2

1 4

NC

NC

3 1

1 3

HIGH*

GND

3 0

1 2

GND

2 9

1 1

BUSY

2 8

1 0

ACK

2 7

9

D7

2 6

8

D6

2 5

7

D5

2 4

6

D4

2 3

5

D3

2 2

4

D2

2 1

3

D1

2 0

2

D0

1 9

1

STROBE

P a r a l l e l

Standard

In compliance with the specifications of Centronics

Input signals

 STROBE (1 BIT), DATA  (8 BIT)

Output signals

BUSY (1 BIT), ACK (1 BIT)

Level of input/output signals

TTL level

Transmission method

Asynchronous

S e r i a l

Standard

 RS-232C specifications

Transmission method

Asynchronous, duplex data transmission

Transmission speed

 2400, 4800, 9600, 19200 (selected using panel keys)

Parity check

 Odd, Even, or None (selected using panel keys)

Data bits

 7 or 8 bits (selected using panel keys)

Stop bits

1 or 2 bits (selected using panel keys)

Handshake

 DTR or Xon/Xoff (selected using panel keys)

Signal 

Number

Terminal 

Number

Signal 

Number

Pin Connection

NC

2 5

1 3

NC

NC

2 4

1 2

NC

NC

2 3

1 1

NC

NC

2 2

1 0

NC

NC

2 1

9

NC

DTR

2 0

8

NC

NC

1 9

7

SG

NC

1 8

6

DSR

NC

1 7

5

CTS

NC

1 6

4

RTS

NC

1 5

3

RXD

NC

1 4

2

TXD

1

FG

(

*

)

The following conditions must be satisfied:

- Material type:  3M Scotchcal Mastercut Film, ARLON Series 2100
- Special stand (a roll material must be set at the rear and on the inner sheet hanger)
- Side margins:  25 mm (1") or more for both the left and right margins
- Front margin:  25 mm (1") or more
(After loading the material, using the display menu to select “EDGE” as the material type automatically sets a front margin of 25 mm (1").)
- Use of the display menu’s “AREA” function to perform feed of the material length plus 0.2 m and set the material correctly
- Cutting of the following data one time

X

Y

Origin

(1)

The letters are cut in order starting with "R"

(2)

After the last letter ("P") has been cut, the machine returns to the origin 

      point and the outer border is cut

The origin is rotated 90 degrees ("AXIS" on the display menu is set to "90deg").

Feed length
Sheets with a width exceeding 610 mm (24"):  4,000 mm (157-7/16")
Sheets with a width of 610 mm (24") or less  :  8,000 mm (315-15/16")

Cut length
Fills the 
hard clip

Front margin:  25 mm (1") or more 

Side margins:  25 mm (1") or more

Side margins:  
25 mm (1") 
or more

Movable 
pinch roller (left)

Movable pinch roller (right)

Cutter 
protector

Interface Specifications

Specification of the Parallel interface

Specification of the Serial interface

3.3K

100

+5 V

+5 V

=

=

*

**

Ω

Ω

1

19

18

36

1

14

13

25