background image

 

7

 

CY-8

1.

 

Use the included connection cable and connect 

the output jack of the CY-8 to the trigger input 

jack of the percussion sound module.

 

Connect the L-shaped plug of the included cable to the CY-
8. This will prevent strain from being applied to the CY-8.

 

To make use of edge shot and choking play techniques, 
you’ll need to connect to a trigger input jack on the 
percussion sound module that accommodates rim shots.

 

2.

 

Leave some slack in the cable to ensure that they are 

not pulled by the movement of the CY-8 when struck.

 

fig.CY04a.e

 

3.

 

Make the trigger settings for the percussion sound 

module. For the recommended values, refer to p. 12.

 

Should you neglect to make the appropriate settings for 

the percussion sound module, you could likely experience 

the following problems:

 

• Sometimes it does not sound (uneven volume)
• The volume is too low (reduced sensitivity)

 

For information on how to change the parameters for a 
percussion sound module, refer to the documentation for 
the percussion sound module you’re using.

 

Playing the CY-8

 

Bow Shot

 

This is the most common playing method, playing the pad face 
of the cymbal. It corresponds to the sound of the “head-side” of 
the connected trigger input.

 

Edge Shot

 

This playing method involves striking the edge with the 
shoulder of the stick. It corresponds to the sound of the “rim-
side” of the connected trigger input.

 

To make use of edge shot, you’ll need to connect to a 
trigger input jack on the percussion sound module that 
accommodates rim shots.

 

Choking

 

Choking (pinching) the cymbal’s edge with the hand 
immediately after hitting the cymbal makes the sound stop.

 

To make use of choking play techniques, you’ll need to 
connect to a trigger input jack on the percussion sound 
module that accommodates rim shots.

 

Specifications

 

CY-8: Cymbal Pad

 

Pad Size:

12 inches

Triggers:

2 (Bow, Edge)

Dimensions: 290 (W) x 295 (D) x 45 (H) mm

11-7/16 (W) x 11-5/8 (D) x 1-7/8 (H) inches

Weight:

650 g / 1 lb 7 oz

Accessories:

Owner’s Manual, Connection Cable, Wing Nut,
Felt Washer, Stopper

Options:

Cymbal Mounts (MDY-7U, MDY-10)
Drum Stands (MDS-3C, MDS-6, MDS-8C, 
MDS-10, MDS-20)

 

962a

 

In the interest of product improvement, the specifications 
and/or appearance of this unit are subject to change without 
prior notice.

Leave some slack
in the cable

Bow

Edge

PD/CY/KD/FD-8_e 7 ページ 2007年7月20日 金曜日 午前9時45分

Summary of Contents for CY-8













Reviews: