14
Mar.2001
SP-303
*
The first number of the 3-digit displayed on the SP-303 and the NUMBER SW
which lights up represent the song number being received and the song number
already received.
6.
When updating is completed, “End” and the Checksum are alternately
displayed.
7.
Turn off the power after checking the Checksum.
*
After all procedures are completed, load user sampling and pattern tone data by
using [Reloading saved data].
TEST MODE &
RESORTING THE FACTORY SETTING
Required items
1. Machine which enables output of note data from MIDI OUT (PC-200 etc.)
2. MIDI cable
3. Oscillator
4. Oscilloscope
5. Noisemeter
6. SmartMedia 1 (FACTORY DATA CARD (P/No.17041008) supplied by
the service center)
7. SmartMedia 2 (3.3V product, initialized with more than 8MB available
space)
*
To perform all test modes, SmartMedia 1 and 2 are required.
*
Always use SmartMedia 2 after initializing by [Initializing SmartMedia].
1. Entering the TEST MODE
Insert the SmartMedia that contains the factory preset data created by the new
product and the SmartMedia (see [SAVING USER DATA & RELOADING
SAVED DATA] for the method) or FACTORY DATA CARD (P/No.17041008)
supplied by the service center, and turn on the power while pressing the
BANK [A], [B], [C] and [D] buttons.
“tst” appears and the test mode starts.
*
Starting the test mode with the following operation enables you to start each test
at a preferred point.
1.
Turn on the power while pressing the BANK [A], [B], [C] and [D] buttons.
-> Enables you to start each test from the beginning.
2.
Turn on the power while pressing the BANK [A], [B] and [C] buttons.
-> Enables you to start from [5. LINE IN/OUT TEST] in the test mode.
3.
Turn on the power while pressing the BANK [B] and [C] buttons.
-> Enables you to perform each test separately.
When turning on the power, “tSt” appears and NUMBER SW [1]-[8] buttons
blink.
The following tests can be executed separately by pressing NUMBER SW [1]-
[8] buttons.
NUMBER SW [1]:1.VERSION & DEVICE CHECK
NUMBER SW [2]:2.SMART MEDIA & SUM CHECK
NUMBER SW [3]:3.SWITCH & LED CHECK
NUMBER SW [4]:4.VOLUME CHECK
NUMBER SW [5]:5.LINE IN/OUT CHECK
NUMBER SW [6]:6.PHONE CHECK
NUMBER SW [7]:7.MIC CHECK
NUMBER SW [8]:8.CARD CHECK
4.
When executing the test in 3. above, after completing all the tests
excluding [1. VERSION & DEVICE CHECK], the [REC] button blinks.
When pressing the [REC] button, NUMBER SW [1]-[8] buttons blink, enabling
tests to be selected separately.
2. Test item list
The [Test mode] includes the following:
Digital circuit test
1.VERSION & DIGITAL CHECK
2.SMART MEDIA & SUM CHECK
3.SWITCH & LED CHECK
4.VOLUME CHECK
8.CARD CHECK
9.MUTE CHECK (*)
11.EFFECT CHECK (*)
12.MIDI CHECK (*)
13.PROTECT CHECK (*)
Analog circuit test
5.LINE IN/OUT CHECK
6.PHONE CHECK
7.MIC CHECK
10.NOISE CHECK (*)
*
Perform this test (*) with in ususal operation mode.
3. Modifying test items
The test items for performing the following operations can be modified during
test mode.
1.
To move from the presently executed test to the previous test item.
-> Press the [DEL] button
(For [3. SWITCH & LED CHECK], press the [DEL] button while pressing the
[CANCEL] button.)
2.
To move from the presently executed test to the next test item.
-> Press the [REC] button
(For [3. SWITCH & LED CHECK], press the [REC] button while pressing the
[CANCEL] button.)
3.
To re-execute the presently executed test.
-> Press the [CANCEL] button
(For [3. SWITCH & LED CHECK], press the [REMAIN] button while pressing
the [CANCEL] button.)
4.
To re-test by escaping an “Err” indication.
-> Press the [CANCEL] button
5.
To select each test from the presently executed test.
-> Press the [DEL] or [REC] buttons.
(Only when entering the test mode from [1. Entering the test mode] 3. For [3.
SWITCH & LED CHECK], return to the selection screen using the [DEL]
button while pressing the [CANCEL] button.)
4. Test contents
Note:
*
During the test mode, do not turn the power off while the dot on the display is blinking,
Otherwise, the memory card and memory data may be destroyed.
1.VERSION & DIGITAL CHECK
Check the version of the machine in use and device function.
1.1VERSION CHECK
After “VEr” appears on the display, the version number of the program of the
Flash ROM (IC22) in actual use appears.
1.2 DEVICE CHECK
The following four tests are executed automatically and the [2.1 SMART
MEDIA CHECK] writing function shown below starts.
Check that the [2.1 SMART MEDIA CHECK] writing function is displayed
without error .
If an error occurs, its content will be displayed.
Re-execute the test after turning on the power again.
(The contents of the error message are written in the [Error message list]).
Summary of Contents for Dr. Sample SP-303
