60
MIDI Parameters
Tx
Select
“On”
if you want the selected part to transmit MIDI data.
Parameter
Value
Tx
Off, On
Tx Ch
Allows you to assign a MIDI transmit channel to the selected part.
Parameter
Value
Tx Ch
1–16
Tx Shift
This parameter allows you to transpose the note messages before
they are transmitted to an external MIDI instrument or computer. The
maximum possible transposition is four octaves up (+48) or down
(–48).
Each step represents a semi-tone.
Parameter
Value
Tx Shift
–48–0–+48
Tx Local
This is where you can disconnect the part from the internal sound
source (
“Off”
)–or re-establish that connection (
“On”
).
Parameter
Value
Tx Local
Off, On
Tx Event
The
“TX Event”
section provides a number of filters that allow you
to specify whether the messages in question should be transmitted
(On) or not (Off).
Filter
Value
Explanation
Program Change
Off, On
Select
“On”
to transmit program change
and bank select (CC00, CC32) messages.
Pitch Bender
Off, On
Select
“On”
to transmit Pitch Bend
messages.
Modulation
Off, On
Select
“On”
to transmit Modulation
messages (CC01).
Volume
Off, On
Select
“On”
to transmit Volume messages
(CC07).
Panpot
Off, On
Select
“On”
to transmit Panpot messages
(CC10).
Expression
Off, On
Select
“On”
to transmit Expression mes-
sages (CC11).
Reverb
Off, On
Select
“On”
to transmit Reverb messages
(CC91).
Chorus
Off, On
Select
“On”
to transmit Chorus messages
(CC93).
All
Off, On
Select
“On”
to transmit all MIDI message
listed above.
Rx
Select
“On”
if you want the selected part to receive MIDI data.
Parameter
Value
Rx
Off, On
Rx Ch
Allows you to assign a MIDI receive channel to the selected part.
Parameter
Value
Rx Ch
1–16
Rx Shift
This parameter allows you to transpose the note messages received
from an external MIDI instrument or computer. The maximum
possible transposition is four octaves up (+48) or down (–48). Each
step represents a semi-tone.
Parameter
Value
Rx Shift
–48–0–+48
Rx Limit Low/Limit High
“Limit Low”
and
“Limit High”
allow you to set the note range to be
received. If not all note messages received on a given MIDI channel
should be played by the selected E-A7 part, narrow down the range.
Parameter
Value
Rx Limit Low
C- –G9
Rx Limit High
C- –G9
NOTE
The
“Limit Low”
value cannot be higher than the
“Limit High”
value (and vice versa).
Rx Event
The
“Rx Event”
section provides a number of filters that allow you
to specify whether the messages in question should be received (On)
or not (Off).
Filter
Value
Explanation
Program Change
Off, On
Select
“On”
to receive program change
and bank select (CC00, CC32) messages.
Pitch Bender
Off, On
Select
“On”
to receive Pitch Bend
messages.
Modulation
Off, On
Select
“On”
to receive Modulation mes-
sages (CC01).
Volume
Off, On
Select
“On”
to receive Volume messages
(CC07).
Panpot
Off, On
Select
“On”
to receive Panpot messages
(CC10).
Expression
Off, On
Select
“On”
to receive Expression mes-
sages (CC11).
Reverb
Off, On
Select
“On”
to receive Reverb messages
(CC91).
Chorus
Off, On
Select
“On”
to receive Chorus messages
(CC93).
Hold
Off, On
Select
“On”
to receive Hold messages
(CC64).
Sostenuto
Off, On
Select
“On”
to receive Sostenuto messag-
es (CC66).
Soft
Off, On
Select
“On”
to receive Soft messages
(CC67).
Caf (Channel
aftertouch)
Off, On
Select
“On”
to receive Caf-Channel
aftertouch.
RPN
Off, On
Select
“On”
to receive Registered param-
eter number messages (CC100/101).
NRPN
Off, On
Select
“On”
to receive Non-registered
parameter number messages (CC98/99).
System Exclusive
Off, On
Select
“On”
to receive System Exclusive
messages.
CC16
Off, On
General purpose controller that allows
you to influence the
“C1”
parameter.
Select
“On”
to receive this message type.
All
Off, On
Select
“On”
to receive all MIDI message
listed above.
