Roland GR-420 User Manual Download

Page: 145 / 501

Turn off the power, turn on the power,

and then load the material again.

If jammed material is caught and

impedes the initial operation when you

turn the power on, perform the

following operations.

1. Turn the power off.

2. Move the cutting carriage to the right

edge of the machine by hand.

3. Turn the power on (the pinch rollers

automatically rise).

4. Remove the jammed material.

• Cutting was performed when thick

material was loaded.

• The material was pulled off suddenly

from the roll without feeding out the

material before cutting.

• An overload was placed on the

machine due to a material jam or

similar cause.

When cutting roll material, pull out the

length of material to be cut from the

roll. Perform a test feed before cutting.

When doing so, set the [AREA] value in

the display menu so that it is around 20

cm longer than the length of the cutting

data.

Loading Roll Material

• When cutting thick material, set the

quality setting to [HEAVY].

Setting Cutting Quality <QUALITY>

Turn off the power, and then move the

machine to a location where it is not

exposed to direct sunlight or intense

indoor lighting. Then, turn on the

power.

The machine is exposed to direct

sunlight or strong indoor lighting and

was not able to detect the origin

immediately after the power was

switched on.

Press any key to clear the error

message. Change the machine's

settings to Tool Mode, and then resend

the data. When doing so, use four crop

marks. When the machine is in Tool

Mode, it is not possible to cut using

three crop marks.

If you want to use three crop marks,

leave the machine in Sensor Mode and

change the shape and color of the crop

marks or the color and glossiness of the

material.

Crop Marks/Tool Marks

Crop Marks Cannot Be Read

Cutting in Tool Mode (1)

Crop marks could not be read in Sensor

Mode.

Press any key to cancel setup and clear

the error message. Load the material

correctly, and then make it ready for

cutting (setup condition).

Loading Position of Material

An attempt was made to ready the

machine without loading material. The

material was removed when the

machine was ready to perform cutting.

The material came loose during cutting.

Switch off the power and contact your authorized Roland DG Corp. dealer.

Install the cutting tool again.

The cutting tool was installed in the

position for cutting perforated lines.

Summary of Contents for GR-420






















































































































































































































































































































































































































































































































Search results

Summary of Contents for GR-420

Reviews:

Related manuals for GR-420

Brands by name

Popular brands

Roland GR-420, User Manual

Search results

Summary of Contents for GR-420

Reviews:

Related manuals for GR-420

Brands by name

Popular brands