background image

2

USING THE UNIT SAFELY

Used for instructions intended to alert the 

user to the risk of injury or material 

damage should the unit be used 

improperly. 
* Material damage refers to damage or 

other adverse effects caused with 

respect to the home and all its 

furnishings, as well to domestic animals 

or pets. 

Used for instructions intended to alert the 

user to the risk of death or severe injury 

should the unit be used improperly. 

The       symbol alerts the user to things that must be 

carried out. The specific thing that must be done is 

indicated by the design contained within the circle. In the 

case of the symbol at left, it means that the power-cord 

plug must be unplugged from the outlet. 

The       symbol alerts the user to important instructions or 

warnings.The specific meaning of the symbol is 

determined by the design contained within the triangle. In 

the case of the symbol at left, it is used for general 

cautions, warnings, or alerts to danger. 
The       symbol alerts the user to items that must never be 

carried out (are forbidden). The specific thing that must 

not be done is indicated by the design contained within 

the circle. In the case of the symbol at left, it means that 

the unit must never be disassembled. 

About       WARNING and       CAUTION Notices

About the Symbols

ALWAYS OBSERVE THE FOLLOWING

 WARNING

• 

Do not open or perform any 

internal modifications on the 

unit.

• 

Do not attempt to repair the 

unit, or replace parts within 

it (except when this manual 

provides specific instructions 

directing you to do so). Refer all servicing 

to your retailer, the nearest Roland 

Service Center, or an authorized Roland 

distributor, as listed on the “Information” 

page.

• 

Never install the unit in any of 

the following locations.

 

6

Subject to temperature 

extremes (e.g., direct 

sunlight in an enclosed 

vehicle, near a heating duct, 

on top of heat-generating 

equipment); or are

 

6

Damp (e.g., baths, washrooms, on wet 

floors); or are

 

6

Exposed to steam or smoke; or are

 

6

Subject to salt exposure; or are

 

6

Humid; or are

 

6

Exposed to rain; or are

 

6

Dusty or sandy; or are

 

6

Subject to high levels of vibration and 

shakiness.

• 

This unit should be used only 

with a stand (MDS series) that is 

recommended by Roland.

• 

When using the unit 

with a stand (MDS series) 

recommended by Roland, the 

stand (MDS series) must be 

carefully placed so it is level and sure to 

remain stable. If not using a stand (MDS 

series), you still need to make sure that 

any location you choose for placing the 

unit provides a level surface that will 

properly support the unit, and keep it from 

wobbling.

 WARNING

• 

Never allow foreign objects 

(e.g., flammable objects, coins, 

wires) or liquids (e.g., water 

or juice) to enter this product. 

Doing so may cause short 

circuits, faulty operation, or 

other malfunctions.

• 

In households with small 

children, an adult should 

provide supervision until the 

child is capable of following all 

the rules essential for the safe operation 

of the unit.

• 

Protect the unit from strong 

impact. 

(Do not drop it!)

 CAUTION

• 

Try to prevent cords and cables 

from becoming entangled. Also, 

all cords and cables should be 

placed so they are out of the 

reach of children.

• 

Never climb on top of, nor place 

heavy objects on the unit.

• 

Should you remove the stopper 

bolt, keep them in a safe place 

out of children’s reach, so there 

is no chance of them being 

swallowed accidentally.

Summary of Contents for KD-180L













Reviews: