background image

27

4(F) = 32nd note triplets (2 Clocks/Step)
5(F) = 64th note triplets (1 Clocks/Step)

Clock source is Master Clock
(F)= Flash

Seq Step Timing

D:3:4

1 = Half Note (48 Clocks/Step)
2 = Quarter note (24 Clocks/Step)
3 = 8th note (12 Clocks/Step)
4 = 8th note, half swing (14,10 Clocks/Step)
5 = 8th note, full swing (16,8 Clocks/Step)
6 = 8th note triplets (8 Clocks/Step)
7 = 16th note (6 Clocks/Step)
8 = 16th note, half swing (7,5 Clocks/Step)
1(F) = 16th note, full swing (8,4 Clocks/Step)
2(F) = 16th note triplets (4 Clocks/Step)3
3(F) = 32nd note (3 Clocks/Step)
4(F) = 32nd note triplets (2 Clocks/Step)
5(F) = 64th note triplets (1 Clocks/Step)

Clock source is Master Clock
(F)= Flash

GLOBAL – Midi and General Settings

Midi In Channel

GA:1:1

1-8 = Channel 1-8 (Midi 0-7)
9-16 = Channel 1-8(F) (Midi 8-15)
All Tone Lights will flash for OMNI

(F)= Flash

Midi Out Channel

GA:1:2

1-8 = Channel 1-8 (Midi 0-7)
9-16 = Channel 1-8(F) (Midi 8-15)

(F)= Flash

Seq Midi Out Channel

GA:1:3

1-8 = Channel 1-8 (Midi 0-7)
9-16 = Channel 1-8(F) (Midi 8-15)

(F)= Flash

Enable Midi CC

GA:1:4

1 = Off
2 = Midi CC Receive Enabled
3 = Midi CC Transmit Enabled
4 = Midi CC Receive & Transmit Enabled

Enable Midi Sysex Receive

GA:1:5

1 = Midi Sysex Receive Disabled
2 = Midi Sysex Receive Enabled

Note – Sysex is Enabled everytime the Kiwi-3P Matrix 
is powered on so editors will work.

Enable Program Change Command

GA:1:6

1 = Off
2 = Midi PC Receive Enabled
3 = Midi PC Transmit Enabled
4 = Midi PC Receive & Transmit Enabled

Enable Midi Soft Through

note - real time midi commands will 
always pass and GA:1:7 will have no 
effect

GA:1:7

1 = Stop All
2 = Pass All
3 = Pass only nonCC
4 = Stop only CC we have used

Enable Midi Clock Generation

GA:1:8

1 = Midi Clock not generated
2 = Midi Clock Generated from Internal

Master Clock Source

GA:2:1

1 = Internal
2 = Midi

www.kiwitechnics.com

Kiwi-3P Matrix Upgrade User Manual v1.2

Summary of Contents for KIWI-3P





























































Reviews: