Roland Micro Composer MC-80 Service Notes Download

Page: 24 / 27

Feb,1999

MC-80

INSTALLING THE SCSI BOARD (VS4S-1)

／

SCSI

ボード（

VS4S-1

）の取り付け方法

♦

Procedure:

1. Turn off the power for the MC-80 and any connected

devices, and disconnect any cables connected to the MC-
80.

2. Turn the MC-80 over, and remove the bottom cover,

(See fig.1 to remove 12 screws.)

◆手順

1. MC-80

と接続している機器の電源を切り、

MC-80

に接続

されているすべてのケーブルを外します。

2. MC-80

を裏返し、ボトムカバーを外します。

（外すネジは

fig.1

を参照してください。）

fig.1 Bottom Cover View

Remove 12 screws circling in this figure./

3. Remove the EXP COVER on the rear panel.

(See fig.2 to remove 2 screws.)

続けてリアパネルの

EXP

カバーを外します。

(

外すネジは

fig.2

を参照してください。）

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWI NG TWO CONDITIONS: (1) THIS DEVICE MAY
NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.

CAUTION

RISQUE DE CHOC
ELECTRIQUE NE PAS
OUVRIR

ATTENTION:

fig.2 Rear Panel View

Remove 2 screws circling in this figure./

4. Insert a supplied fuji-card into the SCSI Board’s

connector(CN1).
Be sure both contacts are facing each other.

5. Insert the SCSI Board, with its parts surface facing

upwards, into the opening of EXP slot.

6. Secure the SCSI Board with 2 screws. Insert the other end

of a fuji-card into the MC-80 JACK BOARD’s
connector(CN108).
(See fig.3 in detail.)

7. Attach a supplied core on the wiring inserted in the MC-80

JACK BOARD’s connector(CN106).
(See fig.3 in detail.)

4. SCSI

ボードの

CN1

に

SCSI

ボード付属のフジカードを挿

します。
フジカードの向きを間違えないように注意してください。

先ほど開けた

EXP

スロットへ、部品面を上にした

VS4S-1

ボードを挿します。

6. SCSI

ボードのパネルをネジで止めた後、フジカードのも

う片方をジャックボード

CN108

に挿します。

(

詳細は

fig.3

を参照してください。）

ジャックボードの

CN106

から出ているワイヤリングに

SCSI

ボードに付属のコアを付けます。

(

詳細は

fig.3

を参照してください。）

CN107

CN110

CN111

CN103

CN105

CN106

MC-80 JACK BOARD

supplied core

supplied fuji-card

Match up blue line on the fuji-card
with white line on the MC-80 JACK BOARD.

fig.3 How to install the supplied core and fuji-card

CN108

8. Re-attach the bottom cover.

9. Checking operation.

a. Prepare an external ZIP drive,a 25pin SCSI cable and a

formatted ZIP disk.

b. Connect the external ZIP drive and SCSI Board

connector with a SCSI cable.

c. Connect the AC cord to the MC-80.
d. Turn on the power for the external ZIP drive.
e. Turn on the MC-80 power while holding down [CHAIN

PLAY],[REC] and [ARPEGGIATOR] at the same time.

f. Insert the ZIP disk into the external ZIP drive after

entering the test mode.

g. After pressing [F6(next)], MC-80 automatically executes

the device checking.

h. The system properly operates, when the SCSI icon is

NOT displayed.
Make sure of the following, when the SCSI icon is
displayed.

SCSI

-Check that the supplied fuji-card is inserted

properly.

Dev Err!

-Check that the external ZIP drive is connected

properly.

No Disk!

-Check that the formatted ZIP disk is inserted into

the external ZIP drive.

10.Executing the operation of shutdown.

a. While holding down the [SHIFT] button, press the [STOP]

button.

b. When "The MC-80 may now be shut down safely"

appears in the display, turn off the power.

* Return the removed EXP COVER with the MC-80 to

customer.

* When using the VS4S-1 with the MC-80,

it has no reference to a VS4S-1 owner’s manual including in
a VS4S-1 package.
However, return the owner’s manual and the package with
the MC-80 to customer.

* "Zip(SCSI)" can be seen in VS4S-1 panel.

However,external SCSI hard disk drives can be also used
with no problem.

ボトムカバーを取り付けます。

動作チェックを行います。

あらかじめ外部

ZIP

ドライブ、

ピン

SCSI

ケーブルお

よびフォーマット済みのディスクを用意しておきます。

外部