background image

24

Error Messages

Message

Meaning

Action

SDCard 

NotReady!

The SD card is not 

inserted, or is inserted 

incompletely.

Turn off the unit, firmly 

insert the SD card, and 

then turn on the unit 

once again.

The SD card was 

removed after you 

selected data that was 

on the SD card.
The format of the SD 

card is invalid.

Use the TR-8S to format 

the SD card (p. 7).

Read Error!

Data could not be read 

from the SD card.

Make sure that the 

SD card is correctly 

inserted.

The file is damaged.

Do not use this file.

Write Error!

Data could not be 

written to the SD card.

Make sure that the 

SD card is correctly 

inserted.

The format of the SD 

card is invalid.

Use the TR-8S to format 

the SD card (p. 7).

SD Card 

Full!

There is insufficient 

space on the SD card.

Delete unneeded data.

Sys Mem 

Damaged!

The contents of the 

TR-8S’s save area may 

be damaged.

Execute the factory 

reset operation (p. 22).
If this does not solve 

the problem, contact 

your dealer or customer 

support.

Message

Meaning

Action

MIDI Buff 

Full!

An unusually large 

amount of MIDI data 

was received, and could 

not be processed.

Reduce the amount of 

MIDI messages that are 

being transmitted.

MIDI 

Offline!

The MIDI IN connection 

was broken.

Check that there is no 

problem with the MIDI 

cable connected to the 

TR-8S’s MIDI IN, and that 

the MIDI cable was not 

disconnected.

Program 

Error!

The TR-8S was unable 

to start up. The program 

could not be read 

correctly. Alternatively, 

the system update 

program may be invalid.

Use the correct program 

to perform the update 

once again. If this does 

not solve the problem, 

contact your dealer or 

customer support.

Now 

Playing!

Since the TR-8S is 

playing, this operation 

cannot be executed.

Stop playback before 

you execute the 

operation.

Now

Recording!

Since the 

TR-8S is recording, this 

operation cannot be 

executed.

Stop recording before 

you execute the 

operation.

Not Found!

The file was not found 

on the SD card.

Make sure that the file 

exists on the SD card.

Main Specifications

Roland TR-8S: RHYTHM PERFORMER

Power Supply

AC Adaptor

Current Draw

2,000 mA

Dimensions

409 (W) x 263 (D) x 58 (H) mm
16-1/8 (W) x 10-3/8 (D) x 2-5/16 (H) inches

Weight

2.1 kg/4 lbs 11 oz

Accessories

AC adaptor, Owner’s manual, Leaflet 

“USING 

THE UNIT SAFELY”

*  This document explains the specifications of the product at the time 

that the document was issued. For the latest information, refer to the 

Roland website.

Summary of Contents for TR-8S

























Reviews: