background image

 

7

 

USING THE UNIT SAFELY

 

When the Head Should Be Replaced

 

The head is an expendable item that eventually will wear out 
and need to be replaced. Replace the head when the following 
occurs:

Slack portions remain in the head even when the head tension 
is properly adjusted.

 

Replacement heads (optional): MH-8 Mesh Head

 

1.

 

Remove all tuning bolts from the PDX-8.

 

fig.Replace.e

 

Do not apply excessive force to the sensor located under 
the head. Doing so can interfere with accurate detection, 
and may damage it.

 

2.

 

Remove the hoop.

 

3.

 

Remove the old head.

 

4.

 

Place the new head on the shell.

 

5.

 

Place the hoop onto the head.

 

6.

 

Attach the tuning bolts to the hoop and shell.

 

7.

 

Next, adjust the tension of the head. Refer to 

“Adjusting the Head Tension” (p. 5).

 

Do not firmly tighten a single tuning bolt by itself. Doing 
so will make it impossible to tension the head evenly, and 
will cause malfunctions.

 

PDX-8

 

Head Size:

8 inches

Triggers:

2 (Head, Rim)

Dimensions:

266 (W) x 326 (D) x 62 (H) mm

10-1/2 (W) x 12-7/8 (D) x 2-1/2 (H) inches

Weight:

1.3 kg

2 lbs 14 oz

Option:

Mesh Head (MH-8)

 

* The Rim rubber is one component that eventually wears out 

(the more so if numerous rim shots are performed), and will 
require replacement. Rim shots may not be performed correctly 
when the rim rubber is worn out. If this occurs, replace the rim 
rubber. Consult Roland Service for more on replacing the rim 
rubber.

 

add

 

* Due to the nature of the materials used in the sensor, changes 

in room temperature may affect the sensitivity of the sensor.

 

Head Replacement

Tuning Key

Hoop

Hoop’s Rubber 
Portion

Sensor

Loosen

Tighten

Shell

Tuning Bolt

Head

 

Specifications

TD-6KW_e 7 ページ 2006年1月24日 火曜日 午後6時3分

Summary of Contents for V-Tour TD-6KW

















Reviews: