22
MIDI Implementations
Start Address
Description
10H 00H 00H
System Preference Area (See 3-2-1)
10H 10H 00H
Clip Control Assignment Area (See 3-2-2)
10H 20H 00H
Color Control Assignment Area (See 3-2-3)
10H 30H 00H
Clip Control Preference Area (See 3-2-4)
* The V-LINK messages received during V-LINK OFF status (: while the unit is in standard mode or MVC mode) will be ignored. However, only the
V-LINK ON message will be received.
* If the unit receives V-LINK ON after MVC ON, the remote control mode switches to V-LINK mode.
* The parameter setting changed using V-LINK messages will not be saved to the internal memory.
* The default values of V-LINK are as below.
Parameters
Assign
Value/Status
Clip Control Ch.
-
1
Color Control Ch.
-
1
Note Control
-
OFF
Transition Time
CC#05
0
Transition Type Sel.
OFF
-
Audio Level
OFF
-
Output Fade
OFF
-
Keyboard Range Lower
-
36
Keyboard Range Upper
-
84
* At the addresses remarked with [#] mark, the data will be divided into 2 bytes : upper nibble (upper 4 bits) and lower nibble (lower 4 bits).
Example) The data to transmit is BCH, 0BH is transmitted as first byte and then 0CH is transmitted as next byte. In case of reception, the unit
ignores if 2 bytes are not received together.
■
3-2-1. System Preference Area
Address
Parameter Name
Sys.Ex.Value
Meaning of Value
10H 00H 00H
V-LINK Enabled
00H - 01H
OFF, ON
10H 00H 01H
V-LINK Rx MIDI Channel (Clip)
00H - 10H
1 - 16 Ch., OFF
10H 00H 02H
V-LINK Rx MIDI Channel (Color)
00H - 10H
1 - 16 Ch., OFF
10H 00H 03H
V-LINK Note Mode
00H, 02H
OFF, Assignable
■
3-2-2. Clip Control Assignment Area
Address
Parameter Name
Sys.Ex.Value
Meaning of Value
#10H 10H 02H
V-LINK Rx Setting (Dissolve Time)
01H-05H,07H-1FH,
Transition Time : Control Change,
40H-5FH,D0H,E0H,FFH
Channel Press, Pitch Bend, OFF
#10H 10H 04H
V-LINK Rx Setting (Audio Level)
01H-05H,07H-1FH,
Audio Level : Control Change,
40H-5FH,D0H,E0H,FFH
Channel Press, Pitch Bend, OFF
#10H 10H 10H
V-LINK Rx Setting (Transition Type)
01H-05H,07H-1FH,
Transition Type : Control Change,
40H-5FH,D0H,E0H,FFH
Channel Press, Pitch Bend, OFF
■
3-2-3. Color Control Assignment Area
Address
Parameter Name
Sys.Ex.Value
Meaning of Value
#10H 20H 20H
V-LINK Rx Setting (Output Fader)
01H-05H,07H-1FH,
Output Fader : Control Change,
40H-5FH,D0H,E0H,FFH
Channel Press, Pitch Bend, OFF
■
3-2-4. Clip Control Preference Area
Address
Parameter Name
Sys.Ex.Value
Meaning of Value
10H 30H 02H
V-LINK Rx Setting
00H - 7FH
Note Number
(Assignable Note Mode : Lower Key)
10H 30H 03H
V-LINK Rx Setting
00H - 7FH
Note Number
(Assignable Note Mode : Upper Key)
3-2. V-LINK
