Appendices
49
Setup Screens
Audio Channels 1–4
(Audio Channel 1–4 [SETUP] Buttons)
Setting item
Value
Explanation
GAIN
0–64 dB
This adjusts the input sensitivity.
LEVEL
0–127
This adjusts the volume level of audio channels 1 through 4.
AUX SEND
0–
100
–127
This adjusts the send level of audio to the AUX bus.
REV SEND
0–
100
–127
This adjusts the send level of audio to Reverb.
PAN
LEFT–
CENTER
–RIGHT
This adjusts the sound position (pan).
EQ HI
-15–15 dB
This boosts or attenuates the high band.
FREQ
700 Hz–
8.00 KHz
–11.0 KHz
This adjusts the center frequency when changing the sound quality in the high band.
EQ MID
-15–15 dB
This boosts or attenuates the middle band.
FREQ
20.0 Hz–
2.50 KHz
–10.0 KHz
This adjusts the center frequency when changing the sound quality in the middle band.
Q
0.5
–16.0
This adjusts the width of the frequency band when boosting or attenuating the middle band.
EQ LO
-15–15 dB
This boosts or attenuates the low band.
FREQ
55 Hz–
110 Hz
–800 Hz
This adjusts the center frequency when changing the sound quality in the low band.
GATE
ON,
OFF
This sets gate on or off.
THRESHOLD
-50–
-48
–0 dB
This sets the level used as the threshold for removing audio. Audio below the level set here is removed.
RELEASE
30–
500
–5000 ms
This adjusts the length of time until the gate effect ends after audio falls below the threshold.
COMP
ON,
OFF
This sets the compressor on or off.
THRESHOLD
-50–
-16
–0 dB
This sets the level used as the threshold when compressing audio. Compression is applied to audio that
exceeds the level set here.
RATIO
1.0:1, 1.2:1, 1.5:1, 2.0:1, 2.8:1, 4.0:1, 8.0:1, 16:1,
INF:1
This specifies the degree of compression applied to the audio. The state in which no compression is
applied is defined as “1.”
ATTACK
0.2–
50
–100 ms
This sets the time until compression starts when audio exceeding the threshold is input.
RELEASE
30–
500
–5000 ms
This adjusts the length of time until compression ends after audio falls below the threshold.
HPF
ON,
OFF
This sets the high-pass filter on or off.
DELAY
0.0
–500.0 ms
This adjusts the delay time for audio.
AUX DELAY
0.0
–500.0 ms
This adjusts the delay time for audio sent to the AUX bus.
SOLO
ON (blue),
OFF
This sets the Solo feature on or off. Only the input audio for the channel which has solo “ON” can be
monitored via headphones.
MUTE
ON (red),
OFF
This sets the Mute feature on or off. Input audio for which this is set to “ON” is silenced.
Audio Channels 5/6 and 7/8
(Audio Channel 5/6 and 7/8 [SETUP] Buttons)
Setting item
Value
Explanation
LEVEL
0–127
This adjusts the volume level of audio channels 5/6 and 7/8.
AUX SEND
0–
100
–127
This adjusts the send level of audio to the AUX bus.
REV SEND
0–
100
–127
This adjusts the send level of audio to Reverb.
EQ HI
-15–15 dB
This boosts or attenuates the high band.
FREQ
700 Hz–
8.00 KHz
–11.0 KHz
This adjusts the center frequency when changing the sound quality in the high band.
EQ MID
-15–15 dB
This boosts or attenuates the middle band.
FREQ
20.0 Hz–
2.50 KHz
–10.0 KHz
This adjusts the center frequency when changing the sound quality in the middle band.
Q
0.5
–16.0
This adjusts the width of the frequency band when boosting or attenuating the middle band.
EQ LO
-15–15 dB
This boosts or attenuates the low band.
FREQ
55 Hz–
110 Hz
–800 Hz
This adjusts the center frequency when changing the sound quality in the low band.
DELAY
0.0
–500.0 ms
This adjusts the delay time for audio.
AUX DELAY
0.0
–500.0 ms
This adjusts the delay time for audio sent to the AUX bus.
SOLO
ON (blue),
OFF
This sets the Solo feature on or off. Only the input audio for the channel which has solo “ON” can be
monitored via headphones.
MUTE
ON (red),
OFF
This sets the Mute feature on or off. Input audio for which this is set to “ON” is silenced.
