9
eng eng
1. Technical data
Use for the intended purpose
WARNING
WARNING
ROLLER’S King 1¼, ROLLER’S King 2 electric die stocks and ROLLER’S Central quick-change die heads for cutting pipe threads for right and left hand threads, for roll
grooving.
All other uses are not for the intended purpose and are therefore prohibited.
1.1. Scope of Supply
ROLLER’S King 1¼ Set C:
Drive unit, counter holder, quick-change die heads ROLLER’S Central R ½", ¾", 1", 1¼",
steel case, instruction manual.
ROLLER’S King 1¼ Set M 20-25-32-40 (M × 1,5):
Drive unit, counter holder, quick-change die heads ROLLER’S Central M 20, M 25, M 32,
M 40 (M × 1,5), steel case, instruction manual.
ROLLER’S King 2 Set C R ½" – 1¼":
Drive unit, counter holder, adapter for die heads up to 1¼", quick-change die heads
ROLLER’S Central R ½", ¾", 1", 1¼", steel case, instruction manual.
ROLLER’S King 2 Set C R ½" – 2":
Drive unit, counter holder, adapter for die heads up to 1¼", quick-change die heads
ROLLER’S Central R ½", ¾", 1", 1¼", 1½", 2", steel case, instruction manual.
ROLLER’S King 2 Set M 20-25-32-40-50 (M × 1,5): Drive unit, counter holder, adapter for die heads up to 1¼" / 40 mm, quick-change die heads
ROLLER’S Central M 20, M 25, M 32, M 40, M 50 (M × 1,5), steel case, instruction manual.
1.2. Article numbers
ROLLER’S King 1¼
ROLLER’S King 2
Drive unit
847309
850309
Adapter for die heads up to 1¼" / 40 mm
479821
ROLLER’S quick-change die heads
see ROLLER catalogue
see ROLLER catalogue
ROLLER’S dies
see ROLLER catalogue
see ROLLER catalogue
Counter holder
847310
850310
ROLLER’S dual purpose holder
543100
543100
Steel cases
847800
850800
Thread-cutting materials
see ROLLER catalogue
see ROLLER catalogue
ROLLER’S Nipparo
see ROLLER catalogue
see ROLLER catalogue
ROLLER’S roller groove device
see ROLLER catalogue
see ROLLER catalogue
1.3. Working range of the quick-change die heads
Thread-Ø
ROLLER’S Central
⅛ –1¼", 16 – 40 mm
⅛ – 2", 16 – 50 mm
Thread types
T
T
Pipe thread R conical (ISO 7-1 EN10226 (DIN 2999 BSPT)), right and left hand thread.
Pipe thread NPT conical (ASME B 1.20.1) Taper Pipe Thread, right hand thread.
Thread for electrical installation tubes M × 1.5 (EN 60423).
Other thread types on request.
Thread length
Standard thread length. ROLLER’S Rola Automatik quick-change die heads open automatically at the
prescribed standard thread length.
Produce nipple
With ROLLER’S Nipparo R ⅜ –1¼" or ⅜ – 2" nipple clamp for right and left hand thread (Fig. 3).
1.4. Speeds of the die head holder (2)
ROLLER’S King 1¼
ROLLER’S King 2
Continuous speed control
35 – 27 rpm
30 – 20 rpm
1.5. Electrical data
230 V
~
1.5. Electrical data
230 V
1.5. Electrical data
230 V , 50 – 60 Hz
230 V
~
, 50 – 60 Hz
230 V
, 50 – 60 Hz
230 V , 50 – 60 Hz
Consumed power
1,200 W
1,200 W
Fuse (mains)
10 A (B)
10 A (B)
Cut-out mode
S3 20% 2/10 min
S3 20% 2/10 min
110 V
~
110 V
110 V , 50 – 60 Hz
110 V
~
, 50 – 60 Hz
110 V
, 50 – 60 Hz
110 V , 50 – 60 Hz
Consumed power
1,200 W
1,200 W
Fuse (mains)
20 A
20 A
Cut-out mode
S3 20% 2/10 min
S3 20% 2/10 min
Protective insulation according to VDE 0740 double insulated or CEE publications 20. The rated current consumption can rise briefl y up to 50% without infl uencing
the function of the unit. The ROLLER’S King 1¼ and ROLLER’S King 2 electric die stocks are equipped with overload protection. The motor is switched off in case of
constant overloading. Press the overload protection (green button) (10) on the motor handle (11) after a short rest period. See also page 5. Faults.
1.6. Dimensions
ROLLER’S King 1¼
ROLLER’S King 2
Unit
480×75×165 mm
492×78×196 mm
Counter holder
260×70×150 mm
415×105×175 mm
1.7. Weight
Unit
4.50 kg
5.70 kg
Counter holder
1.10 kg
2.35 kg
NOTICE
●
Do not dispose of ROLLER’S thread-cutting material undiluted in the drain
system, ground water or ground. Unused thread-cutting material should be
handed in to responsible disposal companies. The waste code for thread-cutting
material containing mineral oil (ROLLER’S Smaragdol) is 120106, for synthetic
(ROLLER’S Rubinol 2000) 120110.
2000
2000
Waste code for thread cutting materials
containing mineral oils (ROLLER’S Smaragdol) and synthetic thread cutting
materials (ROLLER’S Rubinol 2000) in spray cans 150104. Observe the national
regulations.
Explanation of symbols
WARNING
WARNING
Danger with a medium degree of risk which could result in
death or severe injury (irreversible) if not heeded.
CAUTION
CAUTION
Danger with a low degree of risk which could result in minor
injury (reversible) if not heeded.
NOTICE
NOTICE
Material damage, no safety note! No danger of injury.
Read the operating manual before starting
Electrical device complies with protection class II
Environmental friendly disposal
CE conformity mark
