saw and plunge the saw slowly sawing into the material. Preferably use
ROLLER'S reciprocating saws with stepless electronic stroke speed control.
In harder material, e.g. metal, an appropriately large hole for the saw blade
should be drilled for the sawing start.
3.3. Lubricants
Do not use lubricants for normal sawing work. These hinder the ejection of
chips from the sawing chase and therefore reduce the useful life of the saw
blade.
ROLLER'S Smaragdol or ROLLER'S Rubinol for cooling and lubrication should
be used exclusively for sawing stainless steel and hard cast iron pipes. It is
recommended to use ROLLER'S Fox ANC SR and one of the ROLLER'S special
saw blades 561003 ... 561005. The guide holder is absolutely essential for
right-angled sawing (see 2.2.).
4. Maintenance
Not withstanding the maintenance described below, it is recommended to send
in the power tool to an authorised ROLLER contract customer service workshop
for inspection and periodic testing of electrical devices at least once a year. In
Germany, such periodic testing of electrical devices should be performed in
accordance with DIN VDE 0701-0702 and also prescribed for mobile electrical
equipment according to the accident prevention rules DGUV, regulation 3
“Electrical Systems and Equipment”. In addition, the respective national safety
provisions, rules and regulations valid for the application site must be considered
and observed.
4.1. Maintenance
WARNING
Before any repair work, pull the mains plug!
The ROLLER'S reciprocating saws are maintenance-free. The gear runs in a
life-long grease fi lling and therefore needs no lubrication. Keep the saw blade
holder clean. Remove chips from the housing of the saw blade holder. Remove
water/moisture from the housing of the saw blade holder after every use. Lightly
lubricate the saw blade holder and saw blade clamping lever (14) with machine
oil (only ROLLER'S Shark VE). Change a defective locking screw (9) (except
ROLLER'S Shark VE). Clean plastic parts (e.g. housing) only with machine
cleaner or a mild soap and a damp cloth. Do not use household cleaners. These
often contain chemicals which can damage the plastic parts. Never use petrol,
turpentine, thinner or similar products for cleaning.
Make sure that liquids never get inside the machine reciprocating saw. Never
immerse the machine reciprocating saw in liquid.
4.2. Inspection/Servicing
WARNING
Before any repair work, pull the mains plug! This work may only be performed
by qualifi ed personnel.
The ROLLER'S reciprocating saws with universal motor have carbon brushes.
These are subject to wear and must therefore by checked and changed by
qualifi ed specialists or an authorised ROLLER'S customer service workshop
from time to time.
6. Disposal
ROLLER'S reciprocating saws may not be thrown into the domestic waste at
the end of use. They must be disposed of properly by law. Lithium batteries
and battery packs of all battery systems may only be disposed of in the discharged
state, all contacts of incompletely discharged lithium batteries and battery packs
must be covered with insulating tape.
t be covered
t be covered
7. Manufacturer’s Warranty
The warranty period shall be 12 months from delivery of the new product to the
fi rst user. The date of delivery shall be documented by the submission of the
original purchase documents, which must include the date of purchase and the
designation of the product. All functional defects occurring within the warranty
period, which are clearly the consequence of defects in production or materials,
will be remedied free of charge. The remedy of defects shall not extend or
renew the warranty period for the product. Damage attributable to natural wear
and tear, incorrect treatment or misuse, failure to observe the operational
instructions, unsuitable operating materials, excessive demand, use for unau-
thorized purposes, interventions by the customer or a third party or other
reasons, for which ROLLER is not responsible, shall be excluded from the
warranty
Services under the warranty may only be provided by customer service stations
authorized for this purpose by ROLLER. Complaints will only be accepted if
the product is returned to a customer service station authorized by ROLLER
without prior interference in an unassembled condition. Replaced products and
parts shall become the property of ROLLER.
The user shall be responsible for the cost of shipping and returning the product.
The legal rights of the user, in particular the right to make claims against the
seller under the warranty terms, shall not be affected. This manufacturer’s
warranty only applies for new products which are purchased in the European
Union, in Norway or in Switzerland.
This warranty is subject to German law with the exclusion of the United Nations
Convention on Contracts for the International Sales of Goods (CISG).
8. Spare parts lists
For spare parts lists, see www.albert-roller.de → Downloads → Parts lists.
eng eng
5. Faults
5.1. Fault: ROLLER'S reciprocating saw stops during sawing.
Cause:
Remedy:
● Feeding pressure too high.
● Reduce feeding pressure.
● Blunt saw blade (5).
● Change the saw blade.
● Unsuitable saw blade (5).
● Choose a suitable saw blade (see 2.4. and Fig. 8).
● Overload protection (8) has activated (ROLLER'S Fox ANC).
● Wait a few seconds then press the button of the overload protection.
● Worn carbon brushes.
● Have the carbon brushes or DC motor changed by qualifi ed personnel or an
authorised ROLLER customer service workshop.
5.2. Fault: No right-angled cut when sawing pipes with guide holder (2).
Cause:
Remedy:
● Feeding pressure too high.
● Reduce feeding pressure.
● Unsuitable saw blade (5).
● Choose a suitable saw blade (see 2.4. and Fig. 8).
● Blunt saw blade (5).
● Change the saw blade.
● Prism of the guide holder (2) soiled (chips!).
● Clean the prism.
5.3. Fault: ROLLER'S reciprocating saw does not start.
Cause:
Remedy:
● Overload protection has activated (ROLLER'S Fox ANC).
● Wait a few seconds then press the button of the overload protection.
● Mains lead defective.
● Have the mains lead replaced by qualifi ed personnel or an authorised ROLLER
customer service workshop.
● ROLLER'S reciprocating saw defective.
● Have the ROLLER'S reciprocating saw inspected/repaired by an authorised
ROLLER customer service workshop.
5.4. Fault: Centring pin shears off, saw blade (5) cannot be clamped securely enough (ROLLER'S Fox and ROLLER'S Carat all models).
Cause:
Remedy:
● Clamping screw (9) worn.
● Change the clamping screw and/or centring pin.
● Allen key worn (see 2.5.).
● Change the Allen key.
13
Summary of Contents for Akku-Carat 22V VE
Page 24: ...Fig 5 Fig 7 Fig 6 14 5 6 16 3...
