Roller Akku-Disc 100 22 V, Instruction Manual

eng eng

Translation of the Original Instruction Manual

Fig. 1– 10
  1  Cutting wheel drive

  2  Cutting wheel

 3 Rollers

  4  Holes for stand 

(ROLLER’S Disc 100 / 

ROLLER’S Disc 100 RF / 

ROLLER’S Akku-Disc 100 22 V)

  5  Pipe

  6  Feed lever

  7  Safety foot switch

 8 Spindle

  9  Spring plug

10  Height adjustable pipe rest 

11  Clamping lever

12  ROLLER’S Rondo 28-108

13  ROLLER’S Rondo 10-54 E

14  Roller insert for cutting pipes 

Ø 40 – 110 mm (accessory, 

ROLLER’S Disc 225)

15  Pipe guide (Disc 100 RF)

16  Cylinder head screws

17 Stand

18  Machine status check

19  Battery

20  Graduated charging state display

General power tool safety warnings

WARNING

WARNING

Read all safety warnings, instructions, illustrations and specifi cations provided 

with this power tool. Failure to follow all instructions listed below may result in 

electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power 

tool or battery-operated (cordless) power tool.
1)  Work area safety

a)  Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b)  Do not operate power tools in explosive atmospheres, such as in the pres-

ence of fl ammable liquids, gases or dust. Power tools create sparks which 

may ignite the dust or fumes.

c)  Keep children and bystanders away while operating a power tool. Distrac-

tions can cause you to lose control.

2)  Electrical safety

a)  Power tool plugs must match the outlet. Never modify the plug in any way. 

Do not use any adapter plugs with earthed (grounded) power tools. Unmodi-

fi ed plugs and matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces, such as pipes, 

radiators, ranges and refrigerators. There is an increased risk of electric shock 

if your body is earthed or grounded.

c)  Do not expose power tools to rain or wet conditions. Water entering a power 

tool will increase the risk of electric shock.

d)  Do not abuse the cord. Never use the cord for carrying, pulling or unplug-

ging the power tool. Keep cord away from heat, oil, sharp edges or moving 

parts. Damaged or entangled cords increase the risk of electric shock.

e)  When operating a power tool outdoors, use an extension cord suitable for 

outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric 

shock.

f)  If operating a power tool in a damp location is unavoidable, use a residual 

current device (RCD) protected supply. Use of an RCD reduces the risk of 

electric shock.

3)  Personal safety

a)  Stay alert, watch what you are doing and use common sense when oper-

ating a power tool. Do not use a power tool while you are tired or under 

the infl uence of drugs, alcohol or medication. A moment of inattention while 

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection. Protec-

tive equipment such as a dust mask, non-skid safety shoes, hard hat or hearing 

protection used for appropriate conditions will reduce personal injuries.

c)  Prevent unintentional starting. Ensure the switch is in the off-position before 

connecting to power source and/or battery pack, picking up or carrying the 

tool. Carrying power tools with your fi nger on the switch or energising power 

tools that have the switch on invites accidents.

d)  Remove any adjusting key or wrench before turning the power tool on. A 

wrench or a key left attached to a rotating part of the power tool may result in 

personal injury.

e)  Do not overreach. Keep proper footing and balance at all times. This enables 

better control of the power tool in unexpected situations.

f)  Dress properly. Do not wear loose clothing or jewellery. Keep your hair and 

clothing away from moving parts. Loose clothes, jewellery or long hair can be 

caught in moving parts.

g) If devices are provided for the connection of dust extraction and collec-

tion facilities, ensure these are connected and properly used. Use of dust 

collection can reduce dust-related hazards.

h)  Do not let familiarity gained from frequent use of tools allow you to become 

complacent and ignore tool safety principles. A careless action can cause 

severe injury within a fraction of a second.

4)  Power tool use and care

a)  Do not force the power tool. Use the correct power tool for your application. 

The correct power tool will do the job better and safer at the rate for which it was 

designed.

b)  Do not use the power tool if the switch does not turn it on and off. Any power 

tool that cannot be controlled with the switch is dangerous and must be repaired.

c)  Disconnect the plug from the power source and/or remove the battery pack, 

if detachable, from the power tool before making any adjustments, changing 

accessories, or storing power tools. Such preventive safety measures reduce 

the risk of starting the power tool accidentally.

d)  Store idle power tools out of the reach of children and do not allow persons 

unfamiliar with the power tool or these instructions to operate the power 

tool. Power tools are dangerous in the hands of untrained users.

e)  Maintain power tools and accessories. Check for misalignment or binding 

of moving parts, breakage of parts and any other condition that may affect 

the power tool’s operation. If damaged, have the power tool repaired before 

use. Many accidents are caused by poorly maintained power tools.

f)  Keep cutting tools sharp and clean. Properly maintained cutting tools with 

sharp cutting edges are less likely to bind and are easier to control.

g)  Use the power tool, accessories and tool bits etc. in accordance with these 

instructions, taking into account the working conditions and the work to be 

performed. Use of the power tool for operations different from those intended 

could result in a hazardous situation.

h)  Keep handles and grasping surfaces dry, clean and free from oil and grease. 

Slippery handles and grasping surfaces do not allow for safe handling and control 

of the tool in unexpected situations.

5)  Battery tool use and care

a)  Recharge only with the charger specifi ed by the manufacturer. A charger 

that is suitable for one type of battery pack may create a risk of fi re when used 

with another battery pack.

b)  Use power tools only with specifi cally designated battery packs. Use of any 

other battery packs may create a risk of injury and fi re.

c)  When battery pack is not in use, keep it away from other metal objects, like 

paper clips, coins, keys, nails, screws or other small metal objects, that 

can make a connection from one terminal to another. Shorting the battery 

terminals together may cause burns or a fi re.

d) Under abusive conditions, liquid may be ejected from the battery; avoid 

contact. If contact accidentally occurs, fl ush with water. If liquid contacts 

eyes, additionally seek medical help. Liquid ejected from the battery may cause 

irritation or burns.

e)  Do not use a battery pack or tool that is damaged or modifi ed. Damaged or 

modifi ed batteries may exhibit unpredictable behaviour resulting in fi re, explosion 

or risk of injury.

f)  Do not expose a battery pack or tool to fi re or excessive temperature. 

Exposure to fi re or temperature above 130 °C may cause explosion.

g) Follow all charging instructions and do not charge the battery pack or 

tool outside the temperature range specifi ed in the instructions. Charging 

improperly or at temperatures outside the specifi ed range may damage the battery 

and increase the risk of fi re.

6) Service

a)  Have your power tool serviced by a qualifi ed repair person using only 

identical replacement parts. This will ensure that the safety of the power tool 

is maintained.

b)  Never service damaged battery packs. Service of battery packs should only 

be performed by the manufacturer or authorized service providers.

Safety instructions for pipe cutting machines

WARNING

WARNING

Read all safety warnings, instructions, illustrations and specifi cations provided 

with this power tool. Failure to follow all instructions listed below may result in 

electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
● 

Do not use the pipe cutting machine if it is damaged. There is a danger of 

accident.  

●

Do not overload the pipe cutting machine, the cutting wheel (2) and the 

pipe by too high feeding pressure on the feed lever (6). The pipe cutting 

machine and the cutting wheel are subject to heavier wear by too high feeding 

pressure and can be damaged. At too high feeding pressure, the ends of the 

pipe to be cut are pressed further inwards causing constriction of the cross section. 

Pipes made of brittle material, e.g. cast pipes, can be fractured or broken by too 

high feeding pressure.

●

Do not reach into moving parts in the cutting and deburring area and in the 

area of the rollers (3) and height adjustable pipe rests (10). There is a risk 

of injury by crushing fi ngers or hands.

●

Use ROLLER’S Assistent 3B (Art. No. 120120), ROLLER’S Assistent WB 

(Art. No. 120130), ROLLER’S Assistent XL 12

"

 (Art. No. 120125) material 

rest(s) or the height adjustable pipe rest(s) (Fig. 6 (10)) to support long 

pipes at both ends if necessary and align these exactly to the rollers (3) of 

the cutting machine. This reduces untrue running and uncontrolled falling to 

the ground.

●

Check that the pipes are running true before cutting them. Cutting pipes that 

are not straight causes imbalance and the pipe or pipe rest can fall over. The 

pipe can also slip off the material or pipe rest, the pipe cutting machine can move 

and the cutting wheel can be damaged. Danger of injury.

12