Roller Hydro-Polo 22 V, Instruction Manual

eng eng

Safety notes for batteries, rapid chargers, 

power supply units

WARNING

WARNING

Read all safety warnings, instructions, illustrations and specifi cations provided 

with this power tool. Failure to heed the instructions can result in electric shock, 

fi re and/or severe injuries.
Save all warnings and instructions for future reference.
See also www.albert-roller.de → Downloads → Operating Instructions and 

www.albert-roller.de → Downloads → Safety Data Sheets

Explanation of symbols

WARNING

WARNING

    Danger with a medium degree of risk which could result in 

death or severe injury (irreversible) if not heeded.

CAUTION

CAUTION    

Danger with a low degree of risk which could result in minor 

injury (reversible) if not heeded.

NOTICE

Material damage, no safety note! No danger of injury.

Read the operating manual before starting

Electrical device complies with protection class II

Not suitable for using outdoors

Switched-mode power supply (SMPS)

Short-circuit-proof safety transformer (SCPST)

Environmental friendly disposal

CE conformity mark

1.  Technical Data

Intended use

ATTENTION

ATTENTION   

ROLLER’S Hydro-Polo 22 V is intended for cold pressure bending of pipes up to 

90°.

All other uses are not for the intended purpose and are therefore prohibited. 
1.1.  Scope of Supply

ROLLER’S Hydro-Polo 22 V up to Ø 10–32 mm:

Cordless pipe bender, bending formers according to ordered set, 

back former supports H-S Ø 10–26 mm, system case XL-Boxx, 

operating instructions

ROLLER’S Hydro-Polo 22 V INOX Set:

Cordless pipe bender, Ø 15, 18, 22 mm aluminium bending formers, 

back former supports H-S Ø 10 – 26 mm, system case XL-Boxx, 

operating instructions.

1.2.  Article numbers

Drive unit 

153400

Bending formers 

see Fig. 2

Back former support H-S Ø 10–26 mm 

153501

Back former support Ø 32 mm 

153115

Battery Li-Ion 21.6 V, 1.5 Ah 

571570

Battery Li-Ion 21.6 V, 2.5 Ah 

571571

Battery Li-Ion 21.6 V, 5.0 Ah 

571581

Battery Li-Ion 21.6 V, 9.0 Ah 

571583

Rapid charger 220 – 240 V, 70 W 

571575

Rapid charger 100 – 120 V, 70 W 

571575

Rapid charger 100 – 240 V, 90 W 

571585

Rapid charger 100 – 240 V, 290 W 

571587

Voltage supply 220 – 240 V instead of 21.6 V, 15 A batteries 

571567

System case XL-Boxx with inlay 

153455

Angle meter 

590153

1.3. Applications

No cracks or wrinkles shall occur during professional cold bending. Pipe qualities and dimensions which do not guarantee this are not suited to be bent 

with ROLLER’S Hydro-Polo 22 V.

ROLLER’S Hydro-Polo 22 V

ROLLER’S Hydro-Polo 22 V

ROLLER’S Hydro-Polo 22 V 

ROLLER’S Hydro-Polo 22 V INOX

Soft copper pipes, also thin-walled 

Ø 10 – 22 mm, s ≤ 1 mm 

Ø 10 – 22 mm, s ≤ 1 mm

Ø ⅜ – ⅞" 

Ø ⅜ – ⅞"

Soft coated copper pipes  

Ø 10 – 18 mm, s ≤ 1 mm 

Ø 10 – 18 mm, s ≤ 1 mm

Ø ⅜ – ⅝" 

Ø ⅜ – ⅝"

Stainless, nickel steel pipes of the press fi tting systems EN 10217-7, 

EN 10312 series 2, material 1.4401 

Ø 12 – 22 mm, s ≤ 1.2 mm 

Ø 12 – 22 mm, s ≤ 1.2 mm

Stainless steel pipes of the press fi tting systems 

with aluminium bending formers, see fi g. 2 

Ø 15 – 22 mm, s ≤ 1.2 mm

Steel pipes of the press fi tting systems 

with aluminium bending formers, see fi g.2 

Ø 15 – 22 mm, s ≤ 1.5 mm

Soft coated carbon steel pipes 

of the pressfi tting systems EN 10305-3 

Ø 12 – 18 mm, s ≤ 1.2 mm 

Ø 12 – 18 mm, s ≤ 1.2 mm

Soft precision steel pipes 

Ø 10 – 22 mm, s ≤ 1.5 mm 

Ø 10 – 22 mm, s ≤ 1.5 mm

Composite tubes 

Ø  14 – 32  mm 

Ø  14 – 32  mm

Largest bending angle 

90° 90°

Hard copper pipes must be softened by annealing!

Operating temperature range

ROLLER’S Hydro-Polo 22 V 

–10 °C – +60 °C (14 °F – +140 °F)

Battery 

–10 °C – +60 °C (14 °F – +140 °F)

Rapid charger 

0 °C – +40 °C (32 °F – +104 °F)

Voltage supply 

–10 °C – +45 °C (14 °F – +113 °F)

Storage temperature range 

> 0°C (32 °F)

1.4.  Electric Data

ROLLER’S Hydro-Polo 22 V 

  21.6 V –

---, 1.5 Ah / 2.5 Ah / 5.0 Ah / 9.0 Ah

Rapid charger Input  220 – 240 V~;  50 – 60 Hz;  70 W

Output  21.6 V –

---

 all-insulated,  interference-suppressed

Input  100 – 120 V~;  50 – 60 Hz;  70 W

Output  21.6 V –

---

 all-insulated,  interference-suppressed

Rapid charger Input  100 – 240 V~;  50 – 60 Hz;  90 W

Output  21.6 V –

---

 all-insulated,  interference-suppressed

Rapid charger Input  100 – 240 V~;  50 – 60 Hz;  290 W

Output  21.6 V –

---

 all-insulated,  interference-suppressed

Voltage supply

Input  220 – 240 V~;  50 – 60 Hz

Output  21.6 V –

---;  15 A

 all-insulated,  interference-suppressed

1.5.  Dimensions

L × W × H (mm)

ROLLER’S Hydro-Polo 22 V

with back former support 

525 × 250 × 85 (20.7" × 9.8" × 3.3")

1.6.  Weights

ROLLER’S Hydro-Polo 22 V

with back former support, without battery 

3.2 kg (7.1 lb)

Bending  formers  from – to 

0.06 – 0.3 kg  (0.13 – 0.7  lb)

Battery Li-Ion 21.6 V, 1.5 Ah 

0.4 kg (0.9 lb)

Battery Li-Ion 21.6 V, 2.5 Ah 

0.4 kg (0.9 lb)

Battery Li-Ion 21.6 V, 5.0 Ah 

0.8 kg (1.8 lb)

Battery Li-Ion 21.6 V, 9.0 Ah 

1.1 kg (2.4 lb)

1.7.  Noise information

ROLLER’S Hydro-Polo 22 V L

pA

 = 81 dB(A)  L

WA

 = 92 dB(A)  K = 3 dB(A)

1.8.  Vibrations

Weighted effective value of acceleration 

< 2.5 m/s²  K = 1.5 m/s²

The specifi ed vibration emission value was measured according to a standard 

test method and can be used for comparison with another power tool. The 

specifi ed vibration emission value can also be used for an initial estimation of 

the cut-out.

9