background image

17

Rollerdor RD77 Installation Guide,  Edition 2022/01

9. SETTING MOTOR LIMITS

        (SOMFY MOTOR)

fig.9.2

fig.9.1

Your somfy motor comes with a limit cap cover, remove and 
keep the cover safe for later 

(fig.9.1 & 9.2)

.

Using a screw driver press both limits all the way in 
so when you release they will click and hold in place 

(fig.9.3)

.

Curtain already in guides:

 Press and hold the up button 

on receiver box so the curtain starts to roll up around the 
barrel, keep going until there is 1 full slat left in the guide 
runner, then remove the tool box from opening that was 
used to sit the curtain on.

Curtain in arms:

 Press and hold the up button on receiver 

box so the curtain starts to roll up around the barrel, Making 
sure to check the curtain rolls up away from the guide 
runners, the person with the curtain in their arms needs to 
let the curtain unroll and make sure it doesn’t drop when 
you get to the last slats, keep going until the whole curtain 
is up passed the top of the guide. Once passed the guides, 
wind the curtain down so 2 slats are in the opening, then 
press and hold the up button on the receiver box again so 
the curtain goes up. Stop the curtain when 1 full slat is left in 
the guide runners.

Using a screw driver press in and release the coloured limit 
for the open / up direction as per diagram 

(fig.9.5)

.

Run the curtain down until fully compressed and pressure 
is applied from the top via the locking strap. The ideal 
finishing position of the curtain is to have the top of the 
guide runner exactly in the middle of the very top slat 

(fig.9.6)

 but no more than 1 full slat above the top of the 

guide runner 

(fig.9.7)

 if there is more than this you will 

need to remove the extra slats.

Using a screw driver press in and release the coloured limit  
for the close/down direction as per diagram 

(fig.9.5)

.  

Run the curtain all the way to the top limit to check it stops 
in the correct position, then run the curtain all the way to 
the bottom limit to check it stops at the correct position 
and if happy, replace the cap to cover the limits 

(fig.9.1)

. If 

the limits are incorrect repeat procedure from start.

Close the curtain down to make sure it doesn't catch anywhere 
and the front case is not bowed in so as to rub on the curtain 
during operation, then seal down the sides and along the top 
case as needed (silicone sealant is recommended).

fig.9.3

fig.9.4

Summary of Contents for RD77




























Reviews: