5
1. Assemble the Front Wheels ( Fig 1)
- Get washers and snap pins from blister box.
- Slide the small washer (15) onto the axle.
- Slide the front wheel (6) onto the axle. Ensure that the side of the wheel with the
slots is facing out.
- Slide the small washer (15) onto the axle.
- Insert the straight side of the snap pin (14) through the hole at the end of the axle
to keep the wheel in place.
- Position the big hubcap (8) over the holes on the wheel, and snap the hubcap into
place.
- Position the small hubcap (7) over the holes on the big hubcap wheel(8) , and snap
the hubcap into place.
- Repeat above steps for the other front wheel.
7. The Battery Use of Remote Control: (Fig 7)
Buy 2*1.5V AAA batteries, open the battery cover by the screwdriver (not
included). Put the two batteries into the battery cavity with correct polarity.
and put close battery cover lastly.
/ /
@
Forward and reverse
Two working doors
Multifunctional steering wheel with different sound effect
Working LED
With dashboard light front light and daytime running light
3. Assemble the Steering Wheel(Fig 3)
- Plug the steering wheel connector (A) into the dashboard connector (B).
- Slide the steering wheel (2) onto the steering rod
- Align the holes on the steering wheel with the holes on the steering rod.
- Slide the steering wheel screw (12) through the steering wheel and steering rod.
- Fasten the nut (13) to the end of the screw and tighten the screw with a screwdriver.
Right Rear Wheel:
- Slide the right rear wheel (5) onto the axle with the gear teeth facing inward
Ensure that the gear teeth connect with the gear box that is pre-installed on the
axle.
If you encounter trouble fitting both wheels onto the rear axle, then your rear
wheel axle may need to be realigned.
Remove both wheels from the rear wheel axle. Using two hands to push down on
the rear wheel axle and slide it gently toward the side of the vehicle that needs
more room.
4.Assemble Mirrors (Fig 4)
- Align the bottom of the mirror (1) with the hole on the car body
- Gently press the mirror (1) down into place.
- Repeat for the other mirror (1).
5. Assemble the Seat (Fig 5)
- Ensure the lock on the car seat is in the unlock position.
- Align the two hooks on the back of the car seat (3) with the holes on the back of
the battery compartment.
- Insert the hooks into the holes and rotate the seat down into place
- Use a flat head screwdriver or a coin to turn the seat to the locked position.
6. Battery Removal (Fig 6)
- Unlock and remove the seat.
- Disconnect the red battery connector (A) from the red engine connector (B).
- Loosen and remove the screw from the battery strap using a Phillips screwdriver
- Slide the battery strap out from the battery strap slot.
- Remove the battery.
- Note: It is not necessary to remove the battery for charging. However, if the
battery does not reach the outlet, then it can be removed for charging.
2. Assemble the Rear Wheels (Fig 2)
Left Rear Wheel:
- Get washers (16) and snap pins (14) from blister box.
- Slide the big washer (16) onto the axle.
- Slide the Rear wheel orientation rod(17) onto the axle with the wide end facing out.
- Slide the left rear wheel (5) onto the axle with the gear teeth facing inward.
- Slide the big washer (16) onto the axle.
- Insert the straight side of the snap pin (14) through the hole at the end of the
axle to keep the wheel in place.
- Position the big hubcap (8) over the holes on the wheel, and snap the hubcap
into place.
- Position the small hubcap (7) over the holes on the big hubcap (8), and snap
the hubcap into place.
- Slide the big washer (16) onto the axle.
- Insert the straight side of the snap pin (14) through the hole at the end of the
axle to keep the wheel in place.
- Position the big hubcap (8) over the holes on the wheel, and snap the hubcap
into place.
- Position the small hubcap (7) over the holes on the big hubcap (8), and snap
the hubcap into place.
A. Operation Instructions (Fig A):
3. Foot Pedal: Press the foot pedal to put the car in motion. Release to stop. The
headlights will turn on when the car is moving forward.
4.Sound Press the sound button on the steering wheel to make sounds.
1.On/Off Power Switch:press the power switch to “I”, the car will be turned on
.
Press the power switch to “O”, the car will be turned off.
2.Forward/Reverse switch: press the switch to “ ” , Press the foot pedal to
move forward. turn the switch to “ ”,, Press the foot pedal to move backward.
“
”
“
”
“
”
“
”
“
”
“
”
(
)
