background image

GASOLINE BRUSH CUTTER

18

until fuel comes into the primer pump. 10X
2. Pull choke lever up to close choke.
3. Pull starter handle until engine flash fires.
4. 

 Push choke lever down to open choke (excessive cranking with 

choke lever will cause flooding engine making it difficult to start). Pull 
starter handle until engine starts.
5. Allow engine to warm up for a few minutes before using.
6. Allow engine to warm up for a few minutes before using.

.

STARTING WARM ENGINE

If fuel tank was not run dry, pull starter. One to three times and should 
start.

.

DO NOT USE CHOKE

If fuel tank was run dry, after refilling repeat steps 3 thru 6 in. STARTING 
COLD ENGINE. STOPPING THE ENGINE
- Move switch to “O” position

MAINTENANCE & CARE

.

AIR FILTER

- Accumulated dust in the air filter will reduce engine efficiency. Increase 
fuel consumption and allow abrasive particles to pass into the engine. 
Remove the air filter as often as necessary to maintain in a clean 
condition.
- Light surface dust can readily be removed by tapping the filter. Heavy 
deposits should be washed out in suitable solvent.
- Remove filter cover by loosening air filter cover knob.

.

ADJUSTING CARBURETOR NOTE

Do not adjust carburetor unless necessary. If you have trouble with the 
Carburetor, see your dealer. Improper adjustment may cause engine 
damage.

Summary of Contents for 4554



























Reviews: