background image

USER MANUAL

17

to remove valve cause serious personal injury.
Rotate drain valves clockwise until tightly closed.

CHECKING THE SAFETY VALVE

WARNING!

Do not attempt to tamper with the safety valve.

Anything  loosened  from  this  device  could  fly  up  and  hit  you. 

Failure to heed this warning could result death or serious personal 
injury.
The safety valve will automatically release air if the air tank 
pressure exceeds the preset maximum. The valve should be 
checked before each day of use by pulling the ring by hand.

1) Turn the air compressor on and allow the tanks to fill. The 

compressor will shut off when the pressure reaches the preset 
maximum.
2) Turn the air compressor off.

3) Pull the ring on the safety valve to release air for three to five 

seconds.
4) The ring pin must be pushed back into position to stop the 

flow so air at high pressure.

WARNING!

If air leaks after the ring has been released, or if the valve is 
stuck and cannot be actuated by the ring, do not use the air 
compressor until the safety valve has been replaced. Use of the 
air compressor in this condition could result in serious personal 
injury.

MAINTENANCE

WARNING!

When servicing use only identical replacement parts. 
Use of any other parts may create a hazard or cause product 
damage.

15

Summary of Contents for RC-5010






















Reviews: