background image

24 

Ronk Vigilant

®

 Owner’s and Installation Manual

WARRANTY

RONK ELECTRICAL INDUSTRIES, INC.  
Vigilant

®

 Owner Warranty Policy

LIMITED WARRANTY

Ronk Electrical Industries, Inc. will repair or replace, free of 
charge, any part(s) of the equipment that is defective in material or 
workmanship or both providing that installation of the equipment 
complies with all applicable codes, industry standards, laws, 
regulations and provided installation manual. Ronk’s Vigilant

®

 

and associated components shall be installed only by a licensed 
electrical contractor, and otherwise this warranty is void. This 
warranty is effective for the time period and subject to the 
conditions stated below. For warranty service, please call Ronk 
Electrical Industries, Inc. at 1-217-563-8333.

THERE ARE NO OTHER EXPRESS WARRANTIES OR IMPLIED 
WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND 
FITNESS FOR A PARTICULAR PURPOSE. THE ABOVE WARRANTY 
IS LIMITED TO TWO YEARS FROM PURCHASE. ANY AND ALL 
IMPLIED WARRANTIES ARE EXCLUDED AND LIABILITY FOR 
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARE EXCLUDED TO 
THE EXTENT EXCLUSION IS PERMITTED BY LAW. BUYER’S SOLE 
REMEDY IS THE LIMITED WARRANTY STATED ABOVE.  

This warranty only applies to units sold for use in the United States 
of America and Canada.

WARRANTY PERIOD

Consumer Use:  2 years
Commercial Use: 2 years
The warranty period begins on the date of purchase by the first 
retail consumer and continues for the period of time stated 
above. Equipment used for primary power in place of utility is not 
applicable to this warranty.

WARRANTY REGISTRATION PROCESS

Thank you for choosing Ronk’s Vigilant

®

 Series Automatic Transfer 

Switch for your generator system! 

1.  For the fastest and most efficient way to register your Vigilant

®

 

warranty, please complete the online form at ronkelectrical.
com/warranty (preferred method). Otherwise, please complete 
the postcard and return via mail. 

2.  Complete the online form or return the postcard within 10 days 

of installation.

3.  Save the proof of purchase. If the Vigilant

®

 is not registered 

within 10 days, the warranty start date will default to the date of 
purchase by the first retail consumer. 

4.  If the warranty registration steps are not completed, the 

warranty start date will default to the manufacturing date.

ABOUT OUR WARRANTY

Warranty repairs are handled routinely, but sometimes requests 
for warranty service may not be appropriate or applicable. For 
example, warranty service would not apply if equipment damage 
occurred because of misuse, lack of routine maintenance, 
shipping, handling, warehousing, or improper installation. 
Similarly, the warranty is void if the manufacturing date or the 
serial number on the equipment has been removed, altered, or 
modified. During the warranty period defined above, the authorized 
certified technician, at its option, will repair or replace any part 
that, upon examination, is found to be defective under normal 
use and service. No allowances shall be made to the Buyer for 
any transportation, duties, brokerage fees, labor costs, or parts 
adjustments or repairs, or any other work, unless said charges 
have been authorized in writing, in advance, by the Seller. The 
Seller shall not be liable for determining whether any Article(s) 
or parts thereof are suitable for the Buyer’s or any third-party’s 
intended use or application. The Seller shall in no event be liable 
for any special or consequential damages or for loss of profit as 
a result of a breach of this warranty, including without limitation, 
any damages relating to any direct or indirect damage to property 
resulting from any use, removal or installation of the article(s) by 
the Buyer or any third-party.  

This warranty will not cover the following repairs and equipment:

  •   Normal  Wear:

 Electrical equipment, like any mechanical 

device, needs periodic parts and service to perform well.  This 
warranty does not cover repair when normal use has exhausted 
the life of the part or equipment.

  •   Installation and Maintenance:

 This warranty does not apply 

to equipment or parts that have been subjected to improper or 
unauthorized installation or alteration or modification, misuse, 
negligence, accident, overloading, improper maintenance, 
repair or storage so as, in our judgment, to adversely affect its 
performance and reliability.  This warranty also does not cover 
normal maintenance such as adjustments, cleaning and fuse 
replacement.

Other exclusions:

 This warranty excludes wear items or damage 

or malfunctions resulting from accidents, abuse, modifications, 
alterations, or improper servicing. Accessory parts are excluded 
from the product warranty. This warranty excludes failure due 
to acts of God and other force majeure events beyond the 
manufacturer’s control. Also excluded is used, reconditioned, and 
demonstration equipment. The warranty shall not apply to any 
materials or parts thereof furnished by the Buyer, or acquired from 
others at the Buyer’s request and/or the Buyer’s specifications or 
designs.

Summary of Contents for VIGILANT Series





























Reviews: