19
Safety Labels
(8)
(9)
STICKERS ON THE MACHINE
8. Maintenance schedule s cker
9. Electrical fuses/relay loca on s cker
NOTICE
FLASHER
F7
F1
F2
F3
F4
F5
F6
F12
F1
1
F10
F9
F8
10
A
10
A
10
A
20
A
25
A
10
A
40
A
20
A
( OPS )
30A
(NC)
( AUX )
30A
(NO)
( HR )
(NC)
30A
( SU.B )
(NC)
30A
( EOS )
(NC)
30A
( H )
30A
(NO)
( L )
30A
(NO)
( VM )
30A (NO)
( GP )
30A (NO)
DPDT
RELA
Y
USE DESIGNATED FUSES ONLY
TO CHECK DAILY
TO CHECK EVERY 50 HOURS
TO CHECK EVERY 100 HOURS
TO CHECK EVERY 400 HOURS
TO CHECK EVERY 500 HOURS
TO CHECK EVERY 800 HOURS
TO CHECK EVERY 200 HOURS
MAINTENANCE SCHEDULE
MAINTENANCE AREA
THINGS TO CHECK
Main & Side Broom
Inspect brooms for wear and damage, remove strings and debris from bristles and drive assembly
if found.
Air intake system
Empty & clean dust cup of pre-cleaner, Check the air filter clog indicator.
Coolant system
Check coolant level and top up as needed.
Engine
Check engine oil level, Check water seperator visually.
Brake
Check brake oil level and top up as needed.
Inspect the hopper aprons for wear or damage and replace as needed.
Shake and clean hopper dust filters, replace as needed.
Hydraulic system
Check hydraulic oil level and top up as needed.
Wheels and tires
Visually inspect for deflation, wear and damage. Repair or replace as needed.
Miscellaneous
Check belts for wear, Check the hydraulic hoses visually for any leaks or damage.
Hopper
MAINTENANCE AREA
THINGS TO CHECK
Rotate end-to-end.
Inspect broom chamber seals and aprons for wear and damage, adjust or replace as needed.
Perform main broom adjustment test and adjust as needed.
Check functioning of directional control pedal and adjust as needed.
Blow out hydraulic oil cooler fins with compressed air. (If so equipped)
Wheels and tires
Check and tighten front & rear wheel nuts to 200 Nm torque. (For the first time only).
Main Broom
Hydraulic system
MAINTENANCE AREA
THINGS TO CHECK
Clean the engine bay.
Chek and adjust belt tension. (Fan belt & Impeller belt)
Coolant system
Inspect radiator fins and clean as needed.
Check functioning of directional control pedal and adjust if needed.
Check oil level and top up as needed.
Blow out hydraulic oil cooler fins with compressed air. (If so equipped)
Inspect hopper side structure and door seals for wear or damage. Adjust or replace as needed.
Inspect filter frame seals for damages. Adjust or replace as needed.
Hydraulic system
Hopper
Engine
MAINTENANCE AREA
THINGS TO CHECK
Engine
Refer Kubota engine owner's manual.
Clean air filter. NOTE: Clean more often in dusty conditions.
Replace air filter.
Battery
Check water level, clean and tighten battery cable connection.
Steering Cylinder (2 fittings) Lubrication type - grease
Door Cylinder (2 fittings) Lubrication type – grease
Hood Latches & Hinges - Lubrication type - oil
Miscellaneous
Check anti-static drag chain on main broom counter weight for damage or excessive wear.
Make sure the chain is touching the ground at all times.
Air intake system
Lubrication points
MAINTENANCE AREA
THINGS TO CHECK
Engine
Refer Kubota engine owner's manual.
Brake cylinder
Check brake oil line, oil level and top up if needed.
MAINTENANCE AREA
THINGS TO CHECK
Coolant system
Drain and flush the coolant system and top up as needed.
Side broom
Check side broom lift cable, replace if needed.
MAINTENANCE AREA
THINGS TO CHECK
Clean hydraulic oil strainer and breather cap.
Replace hydraulic oil and filter.
Check & tighten front and rear wheel nuts. (Torque to 200 Nm)
Check & tighten wheel motor nuts. (Torque to 640 Nm)
Hydraulic system
Wheels and tires
Summary of Contents for RHINO RD 160
