background image

10

Check Operation of Oven Broil Burner

1. Close the oven door.

2. Press the BROIL pad.

3. Press the START pad.

The oven burner should light within 8 seconds; under certain 
conditions it may take the burner up to 50 to 60 seconds to light. 

Refer to the Use and Care Guide for proper operation of the oven 
controls.

Adjust Oven Broil Burner Flame (if needed)

Look through oven window to check broil burner for proper 
flame. This flame should have a ½" (1.3 cm) long inner cone of 
bluish-green, with an outer mantle of dark blue, and should be 
clean and soft in character. No yellow tips, blowing or lifting of 
flame should occur.

If flame needs to be adjusted:

1. Loosen the lock screw on the air shutter located at the rear of 

the broil burner.

2. Adjust the air shutter as need. 

3. Tighten lock screw.

Replace Oven Racks & Storage or

Warming Drawer

Replace oven racks in oven cavity. Insert storage drawer or 
warming drawer into slide rails on sides of drawer opening. Lift 
front of drawer slightly and push firmly to close drawer.

Complete Installation

1. Check to be sure all parts are now installed. If there is an 

extra part, go back through the steps to see which step was 
skipped.

2. Check to be sure you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check to be sure the range is level. See “Level Range.”

5. Use a mild solution of liquid household cleaner and warm 

water to remove waxy residue caused by protective shipping 
material. Dry thoroughly with a soft cloth. For more 
information, see the “Range Care” section of the Use and 
Care Guide.

6. Read “Range Use” in the Use and Care Guide.

7. Plug into a grounded 3 pronge outlet.

8. Turn on surface burners and oven. See the Use and Care 

Guide for specific instruction on range operation. 

If range does not operate, check the following:

Household fuse is intact and tight; or circuit breaker has not 
tripped.

Range is plugged into a grounded 3 prong outlet.

Electrical supply is connected.

See “Troubleshooting” in the Use and Care Guide.

9. When the range has been on for 5 minutes, feel for heat. If 

you do not feel heat, turn the range off and check to see that 
the gas supply line shutoff valve is open.

If the gas supply line shutoff valve is closed, open it, then 
repeat the 5-minute test as outlined above.

If the gas supply line shutoff valve is open, contact a 
qualified technician.

A. Lock screw

A

Summary of Contents for FGS326RD

















Reviews: