background image

12

3. Apply masking tape to the end of a 

⁵⁄₁₆

" nut driver to help hold 

the gas orifice spud in the nut driver while changing it. Press 
nut driver down onto the gas orifice spud and remove by 
turning it counterclockwise and lifting out. Set gas orifice 
spud aside. 

4. Remove the cardboard orifice spud holder located on the 

back of the range near the gas inlet. Gas orifice spuds are 
stamped with a number, marked with 1 color dot, and have a 
groove in the hex area. Replace the Natural gas orifice spud 
with the correct LP gas orifice spud.

Refer to the following chart for correct LP gas orifice spud 
placement.

LP Gas Orifice Spud Chart for Standard Surface Burners

NOTE: Refer to the Model Number and Serial Number Plate 
located behind the left side of the storage or warming drawer for 
proper sizing of spuds for each burner location.

5. Place Natural gas orifice spuds in the cardboard orifice spud 

holder.

6. Replace the burner base using both screw.

7. Replace burner cap.

8. Repeat steps 1-7 for the remaining burners.

To Convert Oven Bake Burner

1. Remove oven racks.

2. Use a ½" combination wrench to turn the orifice hood down 

snug onto pin (about 2 to 2½ turns).

IMPORTANT: Do not overtighten.

The oven bake burner flame cannot be properly adjusted if 
this conversion is not made. See “Adjust Oven Bake Burner 
Flame” section.

To Convert Oven Broil Burner

Use a ½" combination wrench to turn the orifice hood down snug 
onto the pin (about 2 to 2½ turns).

IMPORTANT: Do not overtighten.

The oven broil burner flame cannot be properly adjusted if this 
conversion is not made. See “Adjust Oven Broil Burner Flame” 
section.

A. Orifice spud
B. Orifice spud holder

C. Screw
D. Spark electrode

A. Groove

Burner Rating

Color

Size

ID Number

12,000 BTU

11,000 BTU

 8,000 BTU

 5,000 BTU

Green/Magenta

Green/Yellow

Green/Lt. Blue 

Green/Brown

1.03 mm

0.99 mm

0.80 mm

0.65 mm

L103

L99

L80

L65

C

B

D

A

A

A. Orifice hood
B. Pin

C. Natural gas: increase gas - increase flame size 

(preset at factory for Natural gas)

D. LP gas: decrease gas - decrease flame size

A. Orifice hood

A

B

C

A

D

A

Summary of Contents for FGS326RD

















Reviews: