Rose electronics ORION lc Installation And Operation Manual Download

Page: 5 / 44

TABLE of CONTENTS

Contents Page #

Disclaimer ...................................................................................................... 1

System introduction ....................................................................................... 1

Features ......................................................................................................... 2

Compatibility .................................................................................................. 2

DDC Information ............................................................................................ 3

Next Frame Switching.................................................................................... 3

KVM Transmitter and Receiver information................................................... 3

Installation Selection ...................................................................................... 4

Multiplex Repeater ..................................................................................... 4

Multiplex Repeater Installation 1 x 7 .......................................................... 4

Multiplex Repeater Installation 2 x 3 .......................................................... 5

Multiplex Repeater Installation 4 x 4 .......................................................... 6

Multiplex Repeater Operation .................................................................... 8

Crosspoint-Switch Installation .................................................................... 9

Crosspoint-Switch Installation – 1 x 7 ........................................................ 9

Crosspoint-Switch Installation – 2 x 6 ...................................................... 10

Crosspoint-Switch Installation – 3 x 5 ...................................................... 11

Crosspoint-Switch Installation – 4 x 4 ...................................................... 12

Crosspoint-Switch Installation – 5 x 3 ...................................................... 13

Crosspoint-Switch Installation – 6 x 2 ...................................................... 14

Crosspoint-Switch Installation – 7 x 1 ...................................................... 15

Crosspoint Switch Operation.................................................................... 16

KVM Switch .............................................................................................. 18

Single Head KVM Switch Installation ................................................... 18

Dual Head KVM Switch Installation ...................................................... 19

Single Head KVM Switch Installation (Cascaded System) .................. 20

KVM Switch Operation (All configurations) .............................................. 21

Operation by Push Button .................................................................... 21

Operation by Keyboard commands ...................................................... 21

Keyboard Commands............................................................................... 23

Serial switching operation ........................................................................ 24

Service Information ...................................................................................... 25

Maintenance and Repair .......................................................................... 25

Technical Support .................................................................................... 25

Troubleshooting - Monitor ............................................................................ 28

Troubleshooting - Keyboard ........................................................................ 28

Troubleshooting – USB- Keyboard/ Mouse ................................................. 29

Summary of Contents for ORION lc













































Search results

Summary of Contents for ORION lc

Reviews:

Related manuals for ORION lc

Brands by name

Popular brands

Rose electronics ORION lc, Installation And Operation Manual

Search results

Summary of Contents for ORION lc

Reviews:

Related manuals for ORION lc

Brands by name

Popular brands