background image

LIMITED WARRANTY 

Copyright Rose Electronics 2018. All rights reserved. 

No part of this manual may be reproduced, stored in a retrieval system, or transcribed in any form or any means, electronic or mechanical, including photocopying and 

recording, without the prior written permission of Rose Electronics. 
manual-rackview-s-series-2018-03-31 

 

Rose Electronics

®

 warrants the sliding RackView-Switch Drawer to be in good working order for one year from 

the date of purchase from Rose Electronics or an authorized dealer. Should this product fail to be in good 
working order at any time during this one-year warranty period, Rose Electronics will, at its option, repair or 
replace the Unit as set forth below. Repair parts and replacement units will be either reconditioned or new. All 
replaced parts become the property of Rose Electronics. This limited warranty does not include service to 
repair damage to the Unit resulting from accident, disaster, abuse, or unauthorized modification of the Unit, 
including static discharge and power surges. 

 

Limited Warranty service may be obtained by delivering this unit during the one-year warranty period to Rose 
Electronics or an authorized repair center providing a proof of purchase date. If this Unit is delivered by mail, 
you agree to insure the Unit or assume the risk of loss or damage in transit, to prepay shipping charges to the 
warranty service location, and to use the original shipping container or its equivalent. You must call for a return 
authorization number first. Under no circumstances will a unit be accepted without a return authorization 
number. Contact an authorized repair center or Rose Electronics for further information.  

 

ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT INCLUDING THE WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO A 
PERIOD OF ONE YEAR FROM THE DATE OF PURCHASE, AND NO WARRANTIES, WHETHER EXPRESS 
OR IMPLIED, WILL APPLY AFTER THIS PERIOD. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW 
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.  

 

IF THIS PRODUCT IS NOT IN GOOD WORKING ORDER AS WARRANTIED ABOVE, YOUR SOLE 
REMEDY SHALL BE REPLACEMENT OR REPAIR AS PROVIDED ABOVE. IN NO EVENT WILL ROSE 
ELECTRONICS BE LIABLE TO YOU FOR ANY DAMAGES INCLUDING ANY LOST PROFITS, LOST 
SAVINGS OR OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF OR 
THE INABILITY TO USE SUCH PRODUCT, EVEN IF ROSE ELECTRONICS OR AN AUTHORIZED DEALER 
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY ANY OTHER 
PARTY.  

 

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR 
CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE ABOVE MAY NOT APPLY TO YOU. 
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS 
WHICH MAY VARY FROM STATE TO STATE. 

 

Summary of Contents for RackView-Switch RV1-CSKVT17/DVI
































Reviews: