background image

8-port Gigabit Desktop Switch 

RC-410LX                                                                   User Manual 

 

FCC STATEMENT 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. 

These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment 

generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful 

interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this 

equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, 

the user is encouraged to try to correct the interference by one or more of the following measures: 

• Reorient or relocate the receiving antenna. 

• Increase the separation between the equipment and receiver. 

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

• Consult the dealer or an experienced radio/ TV technician for help.   

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 

 

1) This device may not cause harmful interference. 

2) This device must accept any interference received, including interference that may cause undesired operation. 

 

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the 

equipment. 

 

CE Mark Warning 

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to 
take adequate measures. 

 

 

- 2 -

Summary of Contents for RC-410LX











Reviews: