background image

11         

Memory 

1K MAC entries   
768K Bits buffer Memory 

Emission 

CE, FCC Class A 

Safety 

LVD 

Power 

Consumption

 

75W Max. 

Operating 

Temperature 

0

0

 ~ 40

0

C (32

0

 ~ 104

0

F) 

Operating 

Humidity 

10% - 90%(non-condensing) 

Power Supply 

Input :100-240V, 50/60MHz, 1.5A Max 
Output

48VDC/1.56A   

 

 

 

 

 

Appendix A:    Troubleshooting 

1.  The Power LED is not lit 

 

Make  sure  the  AC  power  cord  connected  the  Switch  with 

power source properly. 

 

Make sure the power source is ON. 

2.  The Link/Act LED is not lit when a device is connected 

to the corresponding port 

 

Mak

e  sure  that  the  cable  connectors  are  firmly  plugged  into 

the Switch and the device. 

 

Make sure the connected device is turned on and working well. 

 

The cable must be less than 100 meters long (328 feet). 

 

 
 
 
 
 
Thank you for purchasing a quality Rosewill Product. 
Please register your product at: www.rosewill.com for complete warranty 
information and future support for your product. 

 

Rosewill Customer Service Hotline: 1-800-575-9885 
Rosewill Customer Service Support:

 

techsupport@rosewill.com

 

Summary of Contents for RFS-108P












Reviews: