VLT
®
8000 AQUA
■
Unpacking and ordering an AFD
If you are in doubt as to which AFD you have
received and which options it contains, use
the following to find out.
■
Type code ordering number string
On the basis of your order, the AFD is given an
ordering number that can be seen from the nameplate
on the unit. The number may look as follows:
VLT-8008-A-T4-C20-R3-DL-F10-A00-C0
This means that the AFD ordered is a VLT 8008
for three-phase line voltage of 380-480 V (
T4
) in
Compact enclosure IP 20 (
C20
). The hardware variant
is with integral RFI filter, classes A & B (
R3
). The
AFD features a control unit (
DL
) with a PROFIBUS
option card (
F10
). No option card (A00) and no
conformal coating (C0) Character no. 8 (
A
) indicates
the application range of the unit:
A
= AQUA.
Chassis: This enclosure is only available for the larger
power sizes of the VLT 8000 AQUA series. It is
recommended for installation in standard cabinets.
IP 20/NEMA 1: This enclosure is used as standard
enclosure for VLT 8000 AQUA. It is ideal for
cabinet installation in areas where a high degree
of protection is required. This enclose also
permits side-by-side installation.
NEMA 12: This enclosure can be fitted direct to
the wall. Cabinets are not required. IP 54 units
can also be installed side-by-side.
Hardware variant
The units in the program are available in the
following hardware variants:
ST:
Standard unit with or without control
unit. Without DC terminals, except for
VLT 8042-8062, 200-240 V
VLT 8016-8300, 525-600 V
SL:
Standard unit with DC terminals.
EX:
Extended unit for VLT type 8152-8600
with control unit, DC terminals,
connection of external 24 V DC supply
for back-up of control PCB.
DX:
Extended unit for VLT type 8152-8600
with control unit, DC terminals, built-in
line fuses and disconnector, connection
of external 24 V DC supply for back-up
of control PCB.
PF:
Standard unit for VLT 8152-8352 with
24 V DC supply for back-up of control
PCB and built-in main fuses. No DC
terminals.
PS:
Standard unit for VLT 8152-8352 with
24 V DC supply for back-up of control
PCB. No DC terminals.
PD:
Standard unit for VLT 8152-8352
with 24 V DC supply for back-up of
control PCB, built-in main fuses and
disconnect. No DC terminals.
RFI filter
Units for a line voltage of 380-480 V and a motor
power of up to 7.5 kW (VLT 8011) are always
supplied with an integral class A1 & B filter. Units
for higher motor power than these can be ordered
either with or without an RFI filter. RFI filters are
not available for 525-600 V units.
Control unit (keypad and display)
All types of units in the program, except for IP
54 units, can be ordered either with or without
the control unit. IP 54 units always come
with
a
control unit.
All types of units in the program are available with
built-in application options including a relay card
with four relays or a cascade controller card.
Conformal Coating
All types of units in the programme are available
with or without conformal coating of the PCB.
MG.80.A7.22 - VLT is a registered Danfoss trademark
24
Rosewood STP ST42 General (Operation and Maintenance Manual - Part 4:
Section 6.3 Manufacturers Manuals 6.3.33 Danfoss VLT Aquadrive 8000) Vendor Manual
QP Id: VM207
Active: 03/09/2013
Page 30 of 208
