background image

27

E

N

G

L

IS

H

WEAR ADEQUATE CLOTHING

Be sure to wear tight-fitting clothing without any
loose  parts.  Never  wear  open  or  unfastened
jackets, shirts or overalls.

IMPORTANT

To prevent accidents and ensure best performance 

the machine must not be modi-

fied or altered 

unless authorised by the manufacturer. Nor must it be used in condi-

tions or for purposes other than those for which it has been expressly designed. Any

arbitrary modification implemented in this machine will automatically 

exempt the manufac-

turer from any liabilities

for ensuing damage or injury.

This  machine  has  been  designed  and  manufactured  in  conformity  with  EU  directives:

2006/42/CE, 2006/95/CE and 2004/108/CE.

BE SURE TO READ “IMPORTANT” MESSAGES

Information  highlighted  as 

“Important”

in  the  Operator’s  Manual  and/or  machine  indicate

specific 

instructions about settings, maintenance 

and so on. Failure to comply with these

instructions may lead to damage to the machine.

ELECTRICAL SHOCK

For your own personal safety, before connecting the machine to mains:
• check that power mains leading to distribution socket is fitted with an appropriate multipolar

switch protected against overloads and shortcircuits.

• carry  out  all  phase  connections,  as  well  as  any  neutral  and  ground  connections  (compul-

sory) with a standard plug compatible with the above mentioned socket. The protection lead
(ground) is the one with the yellow/green insulating sheath; make sure that the power sup-
ply  cable  is  appropriate  to  its  use,  according  to  length,  mains  voltage  and  machine  con-
sumption.

• unless adequate protections against electrical shock are fitted, do not operate the machine

in damp or wet environments.

Strictly do not start up the machine without the protective panelling. This may jeopar-
dise personnel safety and machine serviceability.

Summary of Contents for TR 110
























Reviews: