10
© 2016,
ROSS
CONTROLS
®
. Content subject to change
.
Online Version
Rev. 11/14/16
General Information
Thread Types by Model Prefix Letter
Pneumatic Port
Prefix Threaded Electrical
Threads
Letter
Opening
NPT
(ANSI B2.1)
None
NPT
ISO 228
- DIN 259 Parallel, BSPP
#
C
*
—
ISO 228
- DIN 259 Parallel, BSPP
#
D
G
ISO 228
- JIS B0203 Tapered
#
J
ISO
SAE
1926- ISO 11926
S
NPT
*
Used only for filters, regulators, lubricators.
#
ISO 228 threads superseds BSPP, G and JIS thread types.
Order Placement
For order placement, consult ROSS or your local ROSS distributor.
For a current list of countries and local distributors, visit ROSS’ website at www.rosscontrols.com.
Standard Specifications
The standard specifications for the products on each page of this
catalog are given on the same page or referenced. For solenoid pilot
valves, models with internal pilot supply are listed. Most models are
also available for use with external pilot supply or have a built-in pilot
supply selector valve.
The products in this catalog are intended for use in industrial pneumatic
systems. Most products are adaptable to other uses and conditions not
covered by the standard specifications given in this catalog. Weights
shown are approximate and are subject to change. Dimensions given,
unless otherwise noted, are envelope dimensions (not for mounting).
Consult ROSS for further information.
Port Threads
Ports of valves and bases described in this catalog have NPT (ANSI
B2.1) threads. Other thread types can be specified by putting an
appropriate prefix letter on the model or part number when ordering.
Flow Ratings
Flow ratings are expressed as C
V
where C
V
= 1 corresponds to a
steady state air flow of approximately 32 scfm under the following
conditions:
Inlet pressure = 100 psig (6.7 bar)
Pressure drop = 10 psi (0.69 bar)
Air temperature = 68°F (20°C)
Relative humidity = 36%
Note:
Because widely differing test standards are used to measure C
V
values, the figures given in this catalog should not be used to compare
ROSS valves with those of other makers. The C
V
ratings given here
are intended only for use with performance charts published by ROSS.
The C
V
ratings are averages for the various flow paths through the
valve and are for steady flow conditions.
Approvals and Certifications
ROSS products are designed to meet a number of industrial standards,
including the Canadian Standards Association (C.S.A.) guidelines.
For more information on specific product approvals, contact your local
distributor or ROSS.
Solenoids
All ROSS standard solenoids are rated for continuous duty (unless
noted otherwise) and will operate the valve within the air pressure
range specified in this catalog.
Explosion-Proof Solenoid Pilot available, for more information
consult ROSS.
Voltage & Hertz
When ordering a solenoid valve, also specify the desired solenoid
voltage and hertz.
Recommended Solenoid Voltages:
100-110 volts AC, 50 Hz;
100-120 volts AC, 60 Hz; 24 volts DC; 110 volts DC.
In addition, the following voltages are available:
200, 220 volts AC, 50 Hz
200, 240, 480 volts AC, 60 Hz
24, 48, 220 volts AC, 50 Hz
240 volts AC, 60 Hz
200, 220 volts AC, 50 Hz
200, 240 volts AC, 60 Hz.
For example: Model 2773B5001, 120 volts AC, 60 Hz.
Model W6076B2401, 220 volts AC, 50 Hz.
Please note that not all configurations are available for all models.
For additional information or help with voltage configuration, please
contact your local distributor or ROSS.
Port Identification
Valve symbols in this catalog conform to the ISO 1219-1:1991
standard of the International Organization for Standardization (ISO)
and the SAE J2051 standard of the Society of Automotive Engineers
(SAE) respectively.
Information or Technical Assistance
For additional information or application assistance concerning ROSS
products, consult ROSS or your local ROSS distributor (see contact
information on the back cover).
Voltage Types by Model Suffix Letter
Voltage
Suffix Letter
120 volts AC
Z
220 volts AC
Y
12 volts DC
H
24 volts DC
W
48 volts DC
M
90 volts DC
K
110 volts DC
P
125 volts DC
C
