2–14 • Configuration
CrossOver 16 User Manual (v4.0)
For More Information on...
• external editor control, refer to the section “Editor
Port” on page 4-17.
• installation and configuration of the TSC-9902
LTC to Serial Converter, refer to your TSC-9902
documentation.
• Live EDL, refer to the section “Live Edit Decision
Lists (EDL)” on page 4-7.
Transition Area Behavior
You can set the behavior of the transition area to suit
your needs.
To configure the Next Transition Area behavior:
1.
Press
MENU
.
2.
Press the
PERS
Wipe Pattern button.
3.
Press
NEXT
until
Trans Area
is displayed.
4.
Press the
Trans Area
knob to display the
Transition Area
menu.
5.
Use the
Trans
knob to set the behavior of
the Next Transition area after a transition is
performed. You can choose from the following:
•
Reset
— The Next Transition area is reset to
a background dissolve transition
•
NotRst
— The Next Transition area is not
reset.
6.
Use the
Auto 2
knob to set the behavior
when a a transition is paused by pressing
AUTO
TRANS
during a transition. You can choose
from the following:
•
HltFwd
— The transition pauses. When you
resume the transition, it completes as
originally set.
•
HltRev
— The transition pauses. When you
resume the transition, the transition proceeds
in reverse and the switcher returns to the
on-air state it was in before the transition was
started.
•
Rev
— The transition immediately reverses
and the switcher returns to the on-air state it
was in before the transition was started.
7.
Use the
ARKey
knob to set whether a Key
remains or is removed from the Next Transition
area after a dedicated key transition is
performed. You can choose from the following:
•
Off
— The Key is removed from the Next
Transition area after a dedicated key
transition is performed.
•
On
— The Key remains active in the Next
Transition area after a dedicated key
transition is performed.
8.
Use the
RlClip
knob to set whether GPI
outputs assigned to input sources are triggered
before a transition. You can choose from the
following:
•
Force
— GPI outputs assigned to input
sources going on-air in a transition are always
triggered.
•
User
— You can choose whether GPI outputs
assigned to input sources going on-air in a
transition are triggered.
NEXT button Secondary Function
You can configure a secondary function of the
NEXT
button allowing it to be used, in conjunction
with the Wipe Pattern buttons, to trigger GPI outputs.
To configure the NEXT button secondary
function:
1.
Press
MENU
.
2.
Press the
PERS
Wipe Pattern button.
3.
Press
NEXT
until
NextBn Func2
is
displayed.
4.
Press the
NextBn Func2
knob to display
the
Secondary Function
menu.
5.
Use the
Func
knob to select the secondary
function for the
NEXT
button. You can
choose from the following:
•
None
— The
NEXT
button is not
assigned a secondary function.
•
GPO
— The
NEXT
button (in
combination with the Wipe Pattern buttons) is
used to trigger GPI outputs.
6.
If you selected
GPO
in the previous step, use
the
Bank
knob to select which GPI output
bank you wish to control.
Note:
• Only one GPI output bank can be triggered at a
time.
MENU
NEXT
NEXT
MENU
NEXT
NEXT
NEXT
NEXT
Summary of Contents for CrossOver 16
