background image

MUX-8258 Series User Guide (v9.0)

Specifications • 47

Specifications

This chapter provides technical specification details on the MUX-8258. Note that specifications are subject to 
change without notice.

MUX-8258-A Technical Specifications

This section includes the technical specifications for the MUX-8258-A. 

Table 3.1  MUX-8258-A Technical Specifications

Category

Parameter

Specification

SDI Input

Number of Inputs

1 HD-SDI

SDI Data Rates and SMPTE 
Standards Accommodated

SMPTE 292M, SMPTE 259M, SMPTE 424M

a

Impedance

75ohm

Return Loss

>15dB to 1.5GHz
>15dB to 3.00GHz

Equalization (Belden 1694A 
cable)

SD: < 450m (1476ft)
HD: < 170m (558ft)
3G: < 100m (328ft)

Connector Type

BNC

SDI Output

Number of Outputs

1

SDI Data Rates and SMPTE 
Standards Accommodated

SMPTE 292M, SMPTE 259M, SMPTE 424M

a

Impedance

75ohm

Return Loss

>15dB to 1.5GHz
>8dB to 3.00GHz

Signal Level

800mV, +/- 10%

DC Offset

<50mV

Rise and Fall Time (20-80%)

SD: 600ps typical
HD: 120ps typical
3G: 130ps typical

Overshoot

<10%

Minimum Video Delay

SD: 7us
HD: 2.2us
3G: 1.1us

Connector Type

BNC

Summary of Contents for MUX-8258 Series

























































Reviews: