background image

18 • Physical Installation

TSI-100 User Guide (v5.0)

2. Re-name the card as follows:

a. Select the 

Settings

 tab.

b. Re-name the card. This will make the card easily identifiable within DashBoard especially when there is 

more than one card to configure.

c. Click 

Apply

.

3. Select the 

TSID Setup

 tab.

4. In the 

TSID Value

 field, enter the 4-digit TSID you wish to match on.

5. In the 

Wrong TSID Count

 field, specify the number of invalid TSIDs that are needed to trigger a change in the 

GPIO state.

6. In the 

No TSID Timeout

 field, specify the amount of time without a TSID before triggering a change in GPIO 

state.

7. Connect the GPIO 1 or GPIO2 output of the TSI-100 to the device you wish to trigger. GPIO1will be low and 

GPIO2 will be high when the transport stream is present and the TSID is correct.

Installing the TSI-100

This section outlines how to install a rear module and card in an openGear frame. 

Rear Modules for the TSI-100

When installing the TSI-100:

DFR-8310 series frames 

— The 

MDL-R10

 Full Rear Module is required.

The TSI-100 is not compatible with the DFR-8310-BNC frames.

DFR-8321 series

OG3-FR series

, and 

OGX-FR series frames

 — The 

MDL-R20

 Full Rear Module is 

required.

Installing a Rear Module

If the Rear Module is installed, proceed to the section “

Installing the TSI-100

” on page 19.

To install a rear module in your openGear frame

1. Locate the card frame slots on the rear of the frame.

2. Remove the Blank Plate from the slot you have chosen for the TSI-100 installation.

3. Install the bottom of the Rear Module in the 

Module Seating Slot

 at the base of the frame’s back plane.

Summary of Contents for openGear TSI-100































Reviews: