background image

and will be repaired without charge for materials or labor within this period. See the “

Warranty and Repair 

Policy

” section in this manual for details.

Environmental Information

The equipment may contain hazardous substances that could impact health and the environment.

To avoid the potential release of those substances into the environment and to diminish the need for the extraction 
of natural resources, Ross Video encourages you to use the appropriate take-back systems. These systems will reuse 
or recycle most of the materials from your end-of-life equipment in an environmentally friendly and health 
conscious manner.

The crossed-out wheeled bin symbol invites you to use these systems.

If you need more information on the collection, reuse, and recycling systems, please contact your local or regional 
waste administration. You can also contact Ross Video for more information on the environmental performances of 
our products.

Company Address

Ross Video Limited

Ross Video Incorporated

8 John Street

P.O. Box 880

Iroquois, Ontario, K0E 1K0

Ogdensburg, New York

Canada

USA 13669-0880

General Business Office: (+1) 613 • 652 • 4886

Fax: (+1) 613 • 652 • 4425

Technical Support: (+1) 613 • 652 • 4886

After Hours Emergency: (+1) 613 • 349 • 0006

E-mail (Technical Support): techsupport@rossvideo.com

E-mail (General Information): solutions@rossvideo.com

Website: http://www.rossvideo.com

Summary of Contents for openGear TSI-100































Reviews: