Ross RABD255/100/2.5 Instructions For Installation, Use And Maintenance Manual Download

Page: 7 / 12

Air Compressor

NOTE: The oil must be changed after the first 10 hrs of opera-
tion then every 50 hrs thereafter.
Recommend compressor oil: Use SAE30 for temperatures
over 10

deg C and use SAE10 below 10 deg C.

Oil Warning :

Check the oil level before using the compressor.

Check the oil level. If necessary add oil until it
reaches the red mark on the sight glass. Do Not over fill.

Assembly

This air compressor requires some minor assemble before it can be used.

Locate the accessory pack/s. These should contain :

1.

Wheel/s and axle set.

Rubber stoppers or caster wheel (100L)

Position the unit on a even surface. Using the hardware provided:-



Fit the wheel/s to the unit.



Fit the rubber stoppers to the legs of the unit.



Oil Filler

Sight glass

Summary of Contents for RABD255/100/2.5













Search results

Summary of Contents for RABD255/100/2.5

Reviews:

Related manuals for RABD255/100/2.5

Brands by name

Popular brands

Ross RABD255/100/2.5, Instructions For Installation, Use And Maintenance Manual

Search results

Summary of Contents for RABD255/100/2.5

Reviews:

Related manuals for RABD255/100/2.5

Brands by name

Popular brands