- 39 -
Computer Instruction
Functions
Program: 21 programs as following
A: 1 Manual Program
B: 10 Preset Program Profi le
P1: ROLLING P2:VALLEY P3: FATBURN P4:RAMP P5:MOUNTAIN
P6: INTERVAL P7:CARDIO P8:ENDURANCE P9:SLOPE P10:RALLY
C: 1 Watt Control Program
D: 4 Heart Rate Control Program
55%H.R, 75%H.R, 90%H.R and TARGET H.R
E: 4 User Setting Programs: CUSTOM1 to CUSTOM4
F: 1 Body Fat Measuring Program
2. Record the user’s data of GENDER, HEIGHT, WEIGHT and AGE even cut off the power.
3. Dot matrix display showing your current status.
4. Simulative ECG measuring the heart rate
5. Display Speed(RPM), TIME, DIST., CAL., WATT, PULSE, LEVEL at the same time.
6. The computer will turn off automatically if there is no operation, speed signal and pulse signal over
4 minutes. Meanwhile,it will store your current exercise data and turn the loading resistance to the
minimum. Once you press any button or in motion, the computer will turn on automatically.
7. Finger-touch-button
Buttons
1. ENTER:
In “stop” mode(display STOP), press ENTER button to enter into program selection and setting
value which fl ash in related window.
A: When you choose the program, press Enter to confi rm the one you like.
B: When in setting, press ENTER to confi rm the value that you would like to preset.
During the start mode(display START), press ENTER to choose display the speed or RPM, or
switch
automatically.
During any mode, hold down this button for 2 seconds to totally reset the computer.
2. START/STOP:
Press START/STOP button to start or stop the programs.
During any mode, hold down this button for 2 seconds to totally reset the computer.
3. UP:
In stop mode and the dot matrix character fl ash, press this button to select the program up. If the
related window value fl ash, press this button to increase the value.
During the start mode(display START), press this button to increase the training resistance.
4. DOWN:
In stop mode and the dot matrix character fl ash, press this button to select the program down. If the
related window value fl ash, press this button to decrease the value.
During the start mode(display START), press this button to decrease the training resistance.
5. PULSE
RECOVERY:
First test your current heart rate and show your heart rate value, press this button to enter into pulse
recovery testing. When you are in pulse recovery mode, press this button to exit.
NOTE:
It is suggested to cover your fi nger within the marked region to select functions in case of any
wrong action.
Operation
1. Turn on the computer
Plug in one end of the adaptor to the AC electrical source and connect the other end to the computer.
The computer will beep and enter into initial mode.
2. Program select and value setting
Manual Program and Preset Program P1 P10
A. Press UP, DOWN button to select the program that you like.
Summary of Contents for 021090 Neutron
