background image

 

1.

 

Introduction 

The TriStar J18 AT automatic turnstile is designed for use in high volume traffic areas to 

control pedestrian traffic. Any type of access control or ticketing system can be used 

to activate the turnstile. The turnstile is operated using a DC brushless motor which 

ensures a smooth operation and the inbuilt encoder guarantees exact positioning of 

the arm. When connected to the fire alarm or other emergency system the active 

arm drops allowing fast exit from the building. During a power failure the arm drops 

and will automatically reposition itself when the power is restored. 

 

2.

 

Technical Specifications 

 

Model No 

TriStar J18 AT 

Throughput 

25 users per minute 

Channel width 

550-600 mm 

Duty cycle 

100% 

Operating input 

Potential free N/O 

MCBF 

300 million operations 

Safety devices 

Arm drops in emergency 

IP rating 

IP 55 standard 

Signal time out 

Adjustable up to 20 seconds 

Power supply 

- 10% 

Motor voltage 

24vdc 

Power consumption 

50W 

Working environment 

30

℃ 

~+

70

℃ 

Relative humidity 

95% 

 

3.

 

Standard features 

3.1

 

Easy set up using the LED display. 

3.2

 

Accurate positioning using the encoder. 

3.3

 

The control panel shows the status of all key components. 

3.4

 

Multiple input and output ports, can be configured to user requirements. 

3.5

 

When the arm is returning to the default position it slows so that there is no 

mechanical force on the internal components. 

3.6

 

Suitable for both Indoor and outdoor.  

3.7

 

The control panel indicates the current status. 

3.8

 

The rotation speed of the arm while entering the turnstile can be adjusted. 

3.9

 

If the arm is forced without presenting a card the arm locks for 4 seconds. 

3.10

 

The turnstile can be opened by two input signals (signals can be input by access 

controller, push button or other equipment). 

3.11

 

Indicator lights: When the turnstile is ready to read the card, the light in the middle will 

be yellow. After reading card the upper blue light will come on. If someone tries to 

push the arm without permission, the red light will come on. 

3.12

 

Single direction or bi direction is optional. 

3.13

 

In an emergency or power failure the active arm will drop. The control panel can be 

Summary of Contents for TRISTAR J18 AT












Reviews: