43
English
VOLUME:
In VARIABLE output mode, this line shows the current volume
setting for remote zone. In FIXED output mode, this volume setting establishes
a permanent fixed output level for the remote zone
TURN ON VOL:
Specifies a default volume level to be used each time
the remote zone is activated. You can select LAST to have the zone activate
with the last previously used volume setting. Or, you specify a volume from
MIN (full mute) to MAX, in 1dB increments. Note that this setting can not
exceed the MAX VOL established in the next line of the menu.
MAX VOL:
Specifies the maximum volume level for the remote zone.
The volume cannot be adjusted above this level. Settings range from MIN
to MAX in 1dB increments.
12V TRIGGER:
The RSP-1572 has six 12V trigger outputs (labeled
1–6) that supply a 12V DC signal to turn on Rotel components and other
components as needed. This menu item turns on specific 12V trigger
outputs whenever the indicated zone is activated. The six 12V Trigger
outputs may be assigned to each zone and can send a turn-on signal
to remote components whenever the remote zones are activated. For
example, ZONE 2 could use 12V Triggers 1, 3 and 6; ZONE 3, 12V
Triggers 2 and 3; ZONE 4, 12V Triggers 5 and 6.
Press the Left/Right buttons on the remote to change the first position
1.
from blank to 1 (activating TRIGGER 1 for that zone).
Press the ENT button on the remote to move to the next position.
2.
Repeat until all six positions are set as desired. A final press of the
3.
SEL button confirms the selection.
Default Setup
D E F A U L T S E T U P
F A C T O R Y D E F A U L T : N o
U S E R D E F A U L T : N o
S E T U S E R D E F A U L T : N o
S E T N EW P A S SWO R D : N o
MA I N ME N U
The DEFAULT SETUP menu provides access to four functions:
Restore all features and settings to the original FACTORY DEFAULT
•
settings.
Memorize a custom group of settings as a USER DEFAULT.
•
Activate the memorized USER DEFAULT settings.
•
Set a NEW PASSWORD for the memorized USER DEFAULT
•
settings.
To restore the FACTORY DEFAULT settings:
Place the highlight on the
FACTORY DEFAULT line using the Up/Down buttons and use the Left/
Right buttons to change the setting to YES. Press the ENT button on the
remote to proceed with resetting to FACTORY DEFAULT. A re-confirmation
screen will appear, please select YES. The unit will power off (to Standby
Mode) and then on, with the factory settings restored. To return to the
HDMI CONTROL:
Options are On, Off. Set to On to enable the ARC
(Audio Return Channel) feature. For ARC to function, your display (TV,
monitor) must be ARC capable and must be connected the RSP-1572’s
HDMI OUT 1(labeled ARC). ARC allows the RSP-1572 to receive the
audio signal from the TV ‘s tuner through the HDMI OUTPUT 1 of RSP-
1572. This allows the audio from the TV to be played through your
hometheater system.
Note:
When ARC is enabled, the Rotel unit will play the audio from
the TV. The volume can be controlled by the TV’s remote control.
Note:
When HDMI control is ON, the unit will pass HDMI Video and
Audio signals in Standby mode direct to the TV. The Rotel unit do not
have to be powered on if you only want to use the speakers of the TV
for audio. But the Rotel unit must be set to the correct input prior to
standby.
POWER CONTROL:
Options are Yes, No. Selecting Yes, allows other
HDMI enabled units in your system to turn the RSP-1572 on or off. In normal
operation, powering ON the source will also turn on the RSP-1572 and
the TV. Turning the TV off, will turn off the RSP-1572 and the source.
Note:
For power control to operate, all components in the system must
have power control enabled from source to displays. Although the unit
has been tested with most major brands of displays and sources, there
may still be occasional compatibility problems.
Zone 2-4 Setup
Z O N E S E T U P
M A I N
M E N U
Z O N E : Z O N E 2
S O U R C E : C D
V I D E O I N P U T : C o m p o s i t e 1
V O L U M E S E T U P : V a r i a b l e
V O L U M E : 6 0
T U R N O N V O L : L a s t
M A X V O L : M a x
1 2 V T R I G G E R : 1 _ 3 _ _ _
The ZONE SETUP menu provides settings and configuration options related
to the operation of the remote zones. This menu is reached by highlighting
the ZONE line on the MAIN menu and pressing ENT.
ZONE:
Specifies the zone to configure, ZONE 2, 3, or 4. Each zone
is configured individually.
SOURCE:
Specifies a source for listening in the selected zone. Options
are CD, TUNER, VIDEO 1-6, SOURCE, and OFF. Selecting the SOURCE
option links the zone source to the source selected for the main zone
so that the remote zone will hear the same source as the main zone.
Selecting the OFF option turns the zone off.
VIDEO INPUT:
Specifies a video source (Composite Video only) for the
selected zone. The options available are Composite 1, 2 and OFF.
VOLUME SETUP:
Configures the remote zone outputs for VARIABLE or
FIXED volume levels. VARIABLE allows control of the volume settings in the
remote zone from the RSP-1572’s front panel or from a remote control/
IR repeater in the zone. FIXED output disables the volume control. In this
mode, the remote zone level can be fixed at the level specified on the
next line, thus optimizing system performance when sending a fixed level
signal to a preamp or amplifier with its own volume adjustment.
