background image

ROTH BAR 1

High-power audio for your living room

4  |  Roth Bar 1 User Manual

Important Safety Instructions

SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR BAR1 AND WIRELESS 
SUBWOOFER AUDIO SYSTEM.

To help you operate these products properly, this section illustrates safety tips which will be of benefit to 
you. Please read it carefully and apply the knowledge you obtain from it to the proper operation of your 
Roth AV BAR1 and Wireless Subwoofer Audio System.

READ BEFORE OPERATING EQUIPMENT

Follow all warnings and instructions marked on this BAR1 and Wireless Subwoofer Audio System.

1.  Read these instructions.
2.  Keep these instructions.
3.  Heed all warnings.
4.  Follow all instructions.
5.  Do not use this apparatus near water.
6.  Clean only with a dry cloth.
7.  Do not block any ventilation openings. Install in 

accordance with the manufacturer’s instructions.

8.  Do not install near any heat sources such as 

radiators, heat registers, stoves, or other apparatus 
(including amplifiers) that produce heat.

9.  Do not defeat the safety purpose of the polarized or 

groundingtype plug. A polarized plug has two blades 
with one wider than the other. A grounding type 
plug has two blades and a third grounding prong. 
The wide blade or the third prong are provided for 
your safety. If the provided plug does not fit into 
your outlet, consult an electrician for replacement of 
the obsolete outlet.

10. Protect the power cord from being walked on 

or pinched particularly at plugs, convenience 
receptacles, and the point where they exit from the 
apparatus.

11. Only use the attachments/accessories specified by 

the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or 

table specified by the manufacturer, or sold with the 
apparatus. When a cart is used, use caution when 
moving the cart/apparatus combination to avoid 
injury from tip-over.

13. Unplug this apparatus during lightning storms or 

when unused for long periods of time.

14. Refer all servicing to qualified service personnel. 

Servicing is required when the apparatus has been 
damaged in any way, such as power-supply cord or 
plug is damaged, liquid has been spilled or objects 
have fallen into the apparatus, the apparatus has 
been exposed to rain or moisture, does not operate 
normally, or has been dropped.

15. The system is designed to comply with the 

recommended safety standards for tilt and stability. 
Do not apply excessive pulling force to the front, or 
top, of the cabinet which could cause the product 
to overturn resulting in product damage and/or 
personal injury.

16. Follow instructions for wall, shelf or ceiling 

mounting as recommended by the manufacturer.

Power Source

This audio system is designed to operate on 230 volts 50 Hz, AC current. Insert the power cords into a 230 
volt 50 Hz outlet. The main plugs are used as the disconnect device and shall remain readily accessible. 
To prevent electric shock, do not use the audio system’s cords with an extension cord, receptacle, or 
other outlet unless the blades and ground terminal can be fully inserted to prevent blade exposure. 
Never connect the audio system to 60 Hz, direct current, or anything other than the specified voltage.

Disposal

Proper disposal of this product. This label indicates that, in the EU, 
electronic devices cannot be disposed of with regular household 
waste. Please use the return or collections systems of your 
municipality or contact the seller where you purchased this product

Please dispose of batteries environmentally friendly. Do not 
dispose of batteries with regular household waste. Please use 
the return or collections systems of your municipality or contact 
the seller where you purchased this product.

Roth SoundBar Manual EH.indd   4

7/3/11   11:19:59

Summary of Contents for BAR 1

















Reviews: