background image

E-M-HP22-V1_21 

Rotronic AG 
Bassersdorf, Switzerland 

Document code 

Unit 

HygroPalm HP22 hand-held indicator: 

User Guide 

Instruction Manual 

Document Type 

Page 

15

 of 16 

Document title 

 
 

© 2009-2010; Rotronic AG                                                                                                                             E-M-HP22-V1_21

 

Environmental limits

 

HP22 

Storage and transit 

-2

0…+70 °C  / 0…100 %RH, non condensing 

Operating limits at electronics 

-

10….60 °C (limited by LC display) 

0…100 %RH, non condensing 

Temperature  limits at probe 

Depends on probe model 

Maximum humidity at probe 

100 %RH up to 80 °C (176 °F) 
75 %RH at 100 °C (212 °F) 
45 %RH at 125 °C (260 °F) 
15 %RH at 150 °C (302 °F) 

Maximum air velocity at probe 

20 m/s (3,935 ft /min) 

Critical environments 

Humidity sensor: as per DV04-14.0803.02 - Critical chemicals 

 

7.2    Dew point accuracy 

See document 

E-M-HC2 Probes

 >

 Dew point accuracy 

8  

Accessories 

For accessories and parts such as the HW4 configuration software, service cables, calibration accessories 
and spare dust filters, please see document 

E-M-HC2-accessories

 

9  

Supporting documents 

 

Document File Name 

Contents 

E-M-HC2 Probes-V1 

HygroClip 2 (HC2) Humidity Temperature Probes, User Guide 

E-M-HC2-accessories 

Accessories and parts for probes, indicators and transmitters 

E-T-AC3000-DF-V1 

AirChip 3000 Description and Main Functions 

E-M-HW4v2-DIR 

List of the HW4 manuals 

E-M-HW4v2-Main 

HW4 software version 2: General instructions and functions common to all 
devices 

E-M-HW4v2-F2-006 

HW4 software version 2: HP22 hand-held indicator and probes 
Device Manager and Data Recording functions 

E-M-HW4v2-A2-001 

HW4 software version 2: Probe Adjustment function AirChip 3000 devices 

E-M-HW4v2-DR-001 

HW4 software version 2: Data Recording Function AirChip 3000 Devices 

E-M-AC3000-CP 

AirChip 3000 Communication Protocol 

E-M-CalBasics 

Temperature and humidity calibration basics 
Instructions for using the ROTRONIC humidity standards 

Summary of Contents for HygroPalm HP22

















Reviews: