background image

E-M-HP22-V1_21 

Rotronic AG 
Bassersdorf, Switzerland 

Document code 

Unit 

HygroPalm HP22 hand-held indicator: 

User Guide 

Instruction Manual 

Document Type 

Page 

5

 of 16 

Document title 

 
 

© 2009-2010; Rotronic AG                                                                                                                             E-M-HP22-V1_21

 

► Data recording 

The data recording function differs from a true data logging 
function in the sense that the AirChip 3000 does not time stamp 
the data. The data recording function can be use to investigate 
events such as a sensor malfunction as well as to retrieve data 
that would otherwise be lost 
 

o

 

Start or stop data recording - up to 2000 value pairs (%RH 
and temperature) 

o

 

Starting a recording session erases all previously recorded 
data 

o

 

The recording mode and log interval can be specified 

o

 

When the device is powered off, the recording session is 
paused but not ended  As long as the recording session 
has not been ended, the device automatically resumes 
recording data when powered up again 

o

 

The recorded data can be downloaded to a PC with the 
HW4 software, time stamped and viewed 

 

MEASUREMENT LOOP VALIDATION 

Functions 

Description 

► Simulator mode 

Used to make the HP22 generate fixed values for the humidity, 
temperature and calculated parameter. Can be configured, 
enabled or disabled 

 

DEVICE SAFEGUARDS 

Functions 

Description 

► Device write protection 

Used to protect the HP22 with a password to prevent 
unauthorized digital access by a digital user. Can be configured, 
enabled or disabled  

► Internal menu access from keypad 

Used to prevent accidental changes to the HP22 settings and 
temperature-humidity adjustment by disabling the MENU key on 
the optional keypad. Can be enabled or disabled 

 

3.2    Factory default settings 

 

Notes: 
 

o

  Configuration of the HP22 and probe by the user and access to its functions requires a PC with the 

ROTRONIC HW4 software (version 2.1.1 or higher) installed. Service cable

 

AC3006 is used to connect the 

HP22 service connector to a USB port of the PC. 

 

o

  Settings and functions that can also be either partially or fully accessed from the keypad are marked with 

the letter 

K

 (see also Operation > Internal Menu). 

Summary of Contents for HygroPalm HP22

















Reviews: