background image

DRIVING THE LOCOMOTIVE MANUALLY 

On manually controlled locomotives, there are three main controls, all of 
which are housed in the cab. 
1) The gas regulator, which should be used to control steam generation as 
described earlier. 
2)  The  reversing  lever.  This  is  in  the  right-hand  side  of  the  cab  and  is 
moved fully forward for running in a forward direction and fully back to 
run in the reverse direction. The lever has a locating stop at either end of 
it’s  travel,  which  have  been  factory  set  for  optimum  forward  or  reverse 
running. In mid gear, the lever sits on a third stop in the centre, but to set 
the  gear  for  running,  it  must  be  sprung  outwards  slightly  as  it  is  moved 
forward or backwards, so that one or other of the stops sits in the hole in 
the  lever.  It  should  be  parked  in  the  centre  (mid  gear)  when  the 
locomotive  is  stationary  for  any  length  of  time.  When  in  mid  gear 
position, the engine will not move under steam power. 
3) The steam regulator. This is the main steam control valve and regulates 
the speed at which the engine will run. The regulator handle is situated in 
the  left  hand  cab  doorway  and  is  moved  anti-clockwise  to  open  and 
clockwise to close. 
Using  the  reversing  lever,  select  the  desired  direction  of  travel  and  open 
the  regulator  a  little.  Initially,  there  will  be  a  certain  amount  of  water  in 
the pipes and cylinders, which will exhaust through the chimney and, after 
a  few  moments,  the  engine  will  move  jerkily,  until  this  clears.  Once  the 
parts have warmed up, the engine will move off steadily and it's speed can 
be  controlled  with  the  regulator.  Subsequent  starts  will  be  quite  smooth 
once the cylinders etc. have reached their normal operating temperature. 
To reverse the locomotive, close the regulator to bring it to  a halt, move 
the reversing lever over and open the regulator again. 
The art of

 

fine control will soon be learnt with a little practice. 

 

DRIVING BY RADIO CONTROL

 

This model is fitted with 2.4 GHz R/C equipment. On a Radio Controlled 
model, speed and direction are controlled by the transmitter. First, turn on 
the  transmitter  and  then  turn  on  the  receiver  on  the  locomotive  with  the 
switch at the front of the tender or coal truck.. The left hand stick on the 
transmitter controls the steam regulator, down for stop up for go. Moving 
to  the  left  or  right  has  no  function.  The  right  hand  stick  operates  the 
reverser, left for forward and right for reverse. This stick is sprung loaded 
to return to it’s central position. Moving up or down has no function 

10

 

Summary of Contents for Blanche





















Reviews: