background image

limited warranty

equipment manufactured by roundup food equipment Division of a.J. antunes & co. has been  

constructed of the finest materials available and manufactured to high quality standards.  these units are 

warranted to be free from mechanical and electrical defects for a period of one year from date of purchase 

or 18 months from shipment from factory, whichever occurs first, under normal use and service, and when 

installed in accordance with manufacturer’s recommendations. to ensure continued proper operation of the 

units, follow the maintenance procedure outlined in the Owner’s Manual.

1. this warranty does not cover cost of installation, defects caused by improper storage or handling prior to plac-

ing of the equipment.  this warranty does not include overtime charges or work done by unauthorized service 

agencies or personnel.  this warranty does not cover normal maintenance, calibration, or regular adjustments 

as specified in operating and maintenance instructions of this manual, and/or labor involved in moving adjacent 

objects to gain access to the equipment.  this warranty does not cover consumable items such as platen release 

sheet and conveyor belt wraps.  

this warranty does not pay travel, mileage, or any other charges for an 

authorized service agency to reach the equipment location.

2. roundup reserves the right to make changes in design or add any improvements on any product.  the right 

is  always  reserved  to  modify  equipment  because  of  factors  beyond  our  control  and  government  regulations.   

changes to update equipment do not constitute a warranty charge.

3. 

If shipment is damaged in transit, the purchaser should make a claim directly upon the carrier.  careful inspec-

tion should be made of the shipment as soon as it arrives and visible damage should be noted upon the car-

rier’s receipt.  Damage should be reported to the carrier.  this damage is not covered under this warranty.

4. Warranty charges do not include freight or foreign, excise, municipal or other sales or use taxes.  all such freight 

and taxes are the responsibility of the purchaser.  

5. tHis WarraNtY is excLusiVe aND is iN Lieu Of aLL OtHer WarraNties, exPresseD Or iMPLieD, 

iNcLuDiNg aNY iMPLieD WarraNtY Or MercHaNtabiLitY Or fitNess fOr a ParticuLar Pur-

POse,  eacH  Of  WHicH  is  HerebY  exPressLY  DiscLaiMeD.    tHe  reMeDies  DescribeD abOVe 

are excLusiVe aND iN NO eVeNt sHaLL rOuNDuP be LiabLe fOr sPeciaL cONsequeNtiaL Or 

iNciDeNtaL DaMages fOr tHe breacH Or DeLaY iN PerfOrMaNce Of tHis WarraNtY.

A.J. Antunes & Co. 

Headquarters/Manufacturing

180 Kehoe Boulevard

Carol Stream, Illinois 60188 USA

Phone (630) 784-1000

Toll Free (800) 253-2991

Fax: (630) 784-1650

Antunes Equipment 

Manufacturing (Suzhou) Ltd.,

9 Hou Ju Road, Building #24,

S&T Park, SND

Suzhou, Jiangsu, China 215011

Phone: 86-512-6841-3637

Fax: 86-512-6841-3907

www.ajantunes.com

Summary of Contents for WD-50

















Reviews: